Kenwood eXcelon KDC-X991 User Manual

English
|
37
8 Enter the name
Operation type Operation
Move the cursor to the enter
character position
Push the Control knob towards right
or left.
Select the character type* Press the Control knob.
Select the characters Turn the Control knob or push it
towards up or down.
* Each time you press the knob, the character type
alternates between the types shown in the table below.
Character type Alphabet upper case
Alphabet lower case
Numbers and symbols
Special characters (Accent characters)
⁄
• Enter characters by using a remote control with numbers
buttons.
Example: If you are entering "DANCE".
Character "D" "A" "N" "C" "E"
Button [3] [2] [6] [2] [3]
Times pressed 11232
9 Confirm the name
Using the Control knob, select "ENTER ".
10 Start recording
Press the Control knob.
Recording track no. and remaining time
"Completed" is displayed when recording
completes.
Canceling recording
1 Cancel recording
Press the [FNC] button.
Exits Import Mode when pressed by step 4.
2 Select "YES"
Select "YES" using the Control knob.
11 Exit Record mode
Select "EXIT" using the Control knob.
Returns to step 3 if "NEXT" is selected.
⁄
• Recording is possible only from music CD and not from
CD containing audio files. Copy audio files from USB
device.
• Sound may skip due to vibration when the vehicle is in
motion. The song will be recorded together with the
skip.
• Normal recording or playback may not be possible with
some CDs.
• DSP cannot be enabled while recording, but it can be
enabled during playback.
• When a song is selected, the remaining recording time is
decreased by the length of the recording. The remaining
recording time is a rough estimate. It may increase of
decrease when recording is completed.
• If recording is canceled or if space runs out while
recording, the recorded songs will remain.
• There is no tag (song information) on the recorded file.
• File name or folder name may contain up to 16
characters.
• If a folder name is specified when recording multiple
songs, the file name will be "foldername_tracknumber".
• If there is a file or folder with the same name, a number
is added as "Name_001".
• If file name or folder name is not specified:
- Single song recording: Files are named sequentially
starting from "CD000_001.wma".
- Multi song recording: Folders are named sequentially
starting from "CD001".
- File and folder name are incremented successively
from the last number even if files in the middle are
deleted. The number returns to 001 when 999 is
reached.
- Setting file name and folder name is recommended.
B64-3767-0000KEnglish.indd37B64-3767-0000KEnglish.indd37 07.5.102:15:58PM07.5.102:15:58PM

Kenwood eXcelon KDC-X991 Specifications

FM Tuner Section

frequency range	87.9 MHz – 107.9 MHz
usable sensitivity	9.3 dBf (0.8 μV/75 Ω)
quieting sensitivity	15.2 dBf (1.6 μV/75 Ω)
frequency response	30 Hz – 15 kHz
signal to noise ratio (MONO)	70 dB
selectivity	≥ 80 dB
stereo separation	40 dB

AM Tuner Section

frequency range	530 kHz – 1700 kHz
usable sensitivity	28 dBμ (25 μV)

CD Player Section

spindle speed	1000 – 400 rpm (CLV 2times)
frequency response	10 Hz – 20 kHz
total harmonic distortion	0.008 %
signal to noise ratio	110 dB
dynamic range	93 dB

USB Interface

usb standard	USB 1.1/ 2.0
maximum supply current	500 mA
file system	FAT16/ 32

Audio Section

maximum output power	50 W x 4
full bandwidth power	22 W x 4
speaker impedance	4 – 8 Ω
tone action band 1	60 – 200 Hz ±9 dB
tone action band 2	250 – 1k Hz ±9 dB
tone action band 3	1.25k – 4k Hz ±9 dB
tone action band 4	5k – 16k Hz ±9 dB
preout level / load	5000 mV/10 kΩ
preout impedance	≤ 80 Ω

Auxiliary Input

frequency response	20 Hz – 20 kHz
input maximum voltage	1200 mV
input impedance	100 kΩ

General

operating voltage	14.4 V
current consumption	10 A
installation size	182 x 53 x 155 mm
weight	3.31 lbs (1.5 kg)