Kenwood eXcelon KDC-X991 User Manual

English
|
63
No Device: The USB device is selected as a source
although no USB device is connected.
N/A Device: An unsupported USB device is connected.
➪ For the supported USB devices, refer to
<http://www.kenwood.com/usb/>.
No Music Data/ Error 15:
• The connected USB device contains no
playable audio file.
• The Internal Memory source contains no
playable audio file.
• Media was played that does not have data
recorded that the unit can play.
USB ERROR: The connected USB device is rated a current
capacity higher than the allowable limit.
➪ Check the USB device with reference to
<http://www.kenwood.com/usb/>.
Some trouble may have occurred to the
connected USB device.
➪ Change the source to any source other
than USB. Remove the USB device.
iPod Error: Connection to the iPod has failed.
➪ Remove the USB device and then
reconnect it.
➪ Confirm that the software for the iPod is
the latest version.
USB REMOVE: The Remove mode has been selected for the
USB device. You can remove the USB device
safely.
Over Capacity: Recording or copying was canceled because
internal memory space ran out while
recording from music CD or copying from
USB device.
➪ Delete unnecessary files and record or
copy once more.
Name Exists. Raname... :
Name Exists. Auto Rename? :
The name entered while recording CD
already exists. Or a file or folder with the same
name already exists while copying from USB
device.
➪ Change the name or delete the existing
file and record or copy once more.
Import Error: Recording is canceled because there is a
scratch on the CD and it cannot be played.
Copy Error: • An incompatible digital audio player was
used.
• Cannot copy because the USB device is not
firmly inserted.
Delete Error:
Format Error: Abnormal condition detected while deleting
or formatting.
➪ Repeat the operation once more. This may
take some time. If the message recurs,
contact your nearest Kenwood dealer.
Can’t Download:
Download Error:
This unit does not work properly for some
reason.
➪ Press the reset button to download it
again. If this error is still displayed, consult
a local Kenwood dealer.
➪ Try all over again from the start. If this error
is still displayed, consult a local Kenwood
dealer.
No Display File:
No file that can be downloaded is contained
in the CD-R/ CD-RW/ USB device.
➪ Make sure that a files created with
referring to <http://www.kenwood.net-
disp.com> is contained in the CD-R/ CD-
RW/ USB device.
Do not delete the extension (.kbm)
created when the file was created.
Incorrect File: The file selected to be downloaded has a
format that this unit cannot read.
➪ Recreate the file.
Writing Error: Writing failed while the file was downloaded.
➪ Try the downloading again.
B64-3767-0000KEnglish.indd63B64-3767-0000KEnglish.indd63 07.5.102:16:12PM07.5.102:16:12PM

Kenwood eXcelon KDC-X991 Specifications

FM Tuner Section

frequency range	87.9 MHz – 107.9 MHz
usable sensitivity	9.3 dBf (0.8 μV/75 Ω)
quieting sensitivity	15.2 dBf (1.6 μV/75 Ω)
frequency response	30 Hz – 15 kHz
signal to noise ratio (MONO)	70 dB
selectivity	≥ 80 dB
stereo separation	40 dB

AM Tuner Section

frequency range	530 kHz – 1700 kHz
usable sensitivity	28 dBμ (25 μV)

CD Player Section

spindle speed	1000 – 400 rpm (CLV 2times)
frequency response	10 Hz – 20 kHz
total harmonic distortion	0.008 %
signal to noise ratio	110 dB
dynamic range	93 dB

USB Interface

usb standard	USB 1.1/ 2.0
maximum supply current	500 mA
file system	FAT16/ 32

Audio Section

maximum output power	50 W x 4
full bandwidth power	22 W x 4
speaker impedance	4 – 8 Ω
tone action band 1	60 – 200 Hz ±9 dB
tone action band 2	250 – 1k Hz ±9 dB
tone action band 3	1.25k – 4k Hz ±9 dB
tone action band 4	5k – 16k Hz ±9 dB
preout level / load	5000 mV/10 kΩ
preout impedance	≤ 80 Ω

Auxiliary Input

frequency response	20 Hz – 20 kHz
input maximum voltage	1200 mV
input impedance	100 kΩ

General

operating voltage	14.4 V
current consumption	10 A
installation size	182 x 53 x 155 mm
weight	3.31 lbs (1.5 kg)