Lenze 8400 protec - Page 169

Diagnostics
Display of operating data, diagnostics
Drive diagnostics via the integrated display
10

169
EDS84DPS424 EN 5.0
Error
Group
SettingCAN codeReactionTextAbbr.NumberID
184
1 0x5401 Ck01 Pos. HW limit switch TroubleQuickStop 0x8600 C00595/1
2 0x5402 Ck02 Neg. HW limit switch TroubleQuickStop 0x8600 C00595/2
7 0x5407 Ck03 Pos. SW limit position TroubleQuickStop 0x8600 C00595/3
8 0x5408 Ck04 Neg. SW limit position TroubleQuickStop 0x8600 C00595/4
153 0x5499 Ck05 Following error 1 Warning 0x8611 C00595/5
154 0x549a Ck06 Following error 2 Warning 0x8611 C00595/6
155 0x549b Ck07 Travel range limit exceeded TroubleQuickStop 0x8612 C00595/7
156 0x549c Ck08 Home position unknown WarningLocked 0x8612 C00595/8
8005 0x54cd Ck09 Positioning mode invalid WarningLocked 0x8600 C00595/9
8007 0x54cf Ck10 Profile data implausible WarningLocked 0x8600 C00595/10
8009 0x54d1 Ck11 Operating mode invalid Warning 0x8600 C00595/11
8014 0x54d6 Ck12 Profile number invalid WarningLocked 0x8600 C00595/12
8015 0x54d7 Ck13 Error FB MCKCtrlInterface Warning 0x8600 C00595/13
15 0x540f Ck14 Target position beyond SW limit
position
WarningLocked 0x8600 C00595/14
5 0x5405 Ck15 Error − brake message signal Fault 0x8600 −
64 0x5440 Ck16 Time overflow − manual operation Fault − −
400
9 0x1a09 dH09 EEPROM power section Fault 0x5530 −
16 0x1a10 dH10 Fan failure Warning 0x5000 C00566/0
104 0x1a68 dH68 Adjustment data error CU Fault 0x5530 −
105 0x1a69 dH69 Adjustment data error BU Fault 0x5530 −
98x
01− US01 User error 1 No reaction 0x6200 C00581/1
1 2 − US02 User error 2 No reaction 0x6200 C00581/2
2 3 − US03 User error 3 No reaction 0x6200 C00581/3
3 4 − US04 User error 4 No reaction 0x6200 C00581/4
4 1 − US05 User error 5 No reaction 0x6200 C00581/5
5 2 − US06 User error 6 No reaction 0x6200 C00581/6
6 3 − US07 User error 7 No reaction 0x6200 C00581/7
7 4 − US08 User error 8 No reaction 0x6200 C00581/8
Group
32 bit error number
ID
Number 16 bit hex error number
Abbr. first part of error message − is also indicated in the device display
Text Full text − visible in the keypad or Engineer
Reaction Lenze setting of the response to the error / event
CAN code CAN emergency error code
Setting Code for setting the response
SO Group error − safety option
CI Group error − fieldbus communication