What to do if the Masimo Monitor displays 'Sensor Off Patient'?
If the Masimo Monitor displays 'Sensor Off Patient', ensure that the CB and CT are properly connected and the sensor is correctly inserted into the patient cable connector. If the issue continues, the sensor, patient cable, or module might be defective and require replacement.
What to do if Masimo Monitor says 'Replace Sensor'?
If the Masimo Monitor prompts 'Replace Sensor', first, check that the sensor is correctly inserted into the patient cable connector. If the sensor has been in use for more than 24 hours, replace it. Also, verify that the sensor's expiration date has not passed.
What to do if the Masimo Monitor displays 'No Sensor Connected'?
If the Masimo Monitor indicates 'No Sensor Connected', verify that the sensor is properly inserted into the patient cable connector. If the problem persists, the sensor, patient cable, or module may be defective and need to be replaced.
How to fix 'High Impedance' error on Masimo Monitor?
To resolve a 'High Impedance' error on the Masimo Monitor, first confirm that all electrodes of the sensor are properly connected. If the problem persists, the sensor may need to be replaced.
How to resolve 'Gel Bridging Detected' on Masimo Monitor?
To resolve a 'Gel Bridging Detected' message on the Masimo Monitor: 1. Clean any gel that has leaked outside of the electrodes on the patient's forehead. 2. Confirm that all electrodes of the sensor are properly connected. 3. If the issue persists, the sensor may need replacement.
How to fix 'SedLine is Disconnected' error on Masimo Monitor?
To resolve a 'SedLine is Disconnected' error on the Masimo Monitor, reconnect the module.
What to do if electrode icons are green or yellow and ARTF display shows artifacts on Masimo sedline?
If the electrode icons on the display of your Masimo Medical Equipment are green or yellow and the ARTF display shows artifacts, first determine if the artifact is indeed the problem by checking the ARTF display. If it is, ask the patient to relax and close their eyes. If the issue continues, consult the Line Power and High Frequency Artifacts section.
What to do if EEG display does not display waveforms for electrodes on Masimo sedline?
If the EEG display on your Masimo Medical Equipment doesn't show waveforms for electrodes, it means the electrode didn't pass the initial impedance check. Here's what you can do: 1. Push and wiggle the white lining around the electrodes to improve contact, but avoid pressing directly on the electrode to prevent gel leakage. 2. Remove the sensor from the patient. 3. Wipe the patient's forehead with alcohol and let it dry. 4. Apply a new sensor. For detailed instructions, refer to the Directions for Use (DFU) for the sensor.
What to do if Sensor Off Patient on Masimo sedline Medical Equipment?
To address a 'Sensor Off Patient' message on your Masimo Medical Equipment, follow these steps: 1. Ensure that the CB and CT are properly connected. 2. Verify that the sensor is correctly inserted into the patient cable connector. 3. If the issue persists, the sensor, patient cable, or module may be defective and require replacement.
What to do if High Impedance on Masimo sedline Medical Equipment?
To resolve a 'High Impedance' alert on your Masimo Medical Equipment, ensure that all electrodes of the sensor are properly connected. If the problem persists, the sensor may need to be replaced.
Specifies the intended clinical environments for the SedLine Monitor's application.
States the age restriction for using the SedLine Sedation Monitor.
Details the SedLine Module, Patient Cable, and Sensor(s).
Essential checks and confirmations required before operating the SedLine monitor.
Instructions on connecting the module to the patient cable and Root.
Access and configure settings for various SedLine monitored parameters.
Configure EEG and DSA settings, and SedLine Sensor information.
Activates the recording and storage of EEG waveforms to a USB stick.
Resolving issues with unavailable trends, impedance, and artifacts.
Solutions for line power and high frequency interference artifacts.
General| Channels | 4 EEG channels |
|---|---|
| Parameters | EMG |
| Connectivity | Ethernet, USB |
| Compatibility | Masimo Root |
| Application | sedation monitoring |
| Power Source | Battery |
To Next Page
