Miditemp MP 22-W - Merge Assignment (MER); Save Assignment (SAV)

MIDITEMP MP 22-W, MP 22-CD, MP 88-W, MP 88-CD, PMM 88-E, MT 16-X
MIDITEMP MP 22-W, MP 22-CD, MP 88-W, MP 88-CD, PMM 88-E, MT 16-XMIDITEMP MP 22-W, MP 22-CD, MP 88-W, MP 88-CD, PMM 88-E, MT 16-X
MIDITEMP MP 22-W, MP 22-CD, MP 88-W, MP 88-CD, PMM 88-E, MT 16-X
5
1
2.2.2 Merge Assignment
2.2.2 Merge Assignment2.2.2 Merge Assignment
2.2.2 Merge Assignment (MER)
(MER) (MER)
(MER)
This function allows to add an Assignment from disk to the one in the temporary memory of
the MULTIPLAYER, thus creating one complete Assign from two partial ones.
$
Press
and to switch into the “<Sequencer>“ menu.
$
Select
»ASG«.
➊
With
»
MER
« and the data wheel
!
you can select the required Assign file.
➋
If you want to change the drive now just press
and select the drive.
➌
If you see the name of the ASSIGN in the lower line confirm with
.
%
With
you leave the function.
IMPORTANT:
IMPORTANT:IMPORTANT:
IMPORTANT:
The unit will always give priority to the Assignments loaded from disk over those in its internal
The unit will always give priority to the Assignments loaded from disk over those in its internalThe unit will always give priority to the Assignments loaded from disk over those in its internal
The unit will always give priority to the Assignments loaded from disk over those in its internal
memory. If you need to get around this, save the Assignment in memory first under a new name, then
memory. If you need to get around this, save the Assignment in memory first under a new name, thenmemory. If you need to get around this, save the Assignment in memory first under a new name, then
memory. If you need to get around this, save the Assignment in memory first under a new name, then
load the other Assign file, and finally call up the Merge function and merge the file you just saved
load the other Assign file, and finally call up the Merge function and merge the file you just savedload the other Assign file, and finally call up the Merge function and merge the file you just saved
load the other Assign file, and finally call up the Merge function and merge the file you just saved
under the new name. Of course, the priorities will now be the other way round!
under the new name. Of course, the priorities will now be the other way round!under the new name. Of course, the priorities will now be the other way round!
under the new name. Of course, the priorities will now be the other way round!
2.2.3 Save Assignment (SAV)
2.2.3 Save Assignment (SAV)2.2.3 Save Assignment (SAV)
2.2.3 Save Assignment (SAV)
To fix all your settings of the session concerning the Assign (see page 49, “2.1 The Assign
file“), which stay at this moment in the temporary memory of the MULTIPLAYER and would be lost
after switching the unit off, you should use this function. To get them back later you will save them as
an “ASSIGN FILE“. Everytime using this function all entries of the Assign are saved together!
$
Press
and to switch into the “<Sequencer>“ menu.
$
Select
»ASG«.
➊
Press
»
SAV
« and the default name ”
ASSIGN.ASG
” appears in the display.
➋
If you want to change the drive just press
and select the drive, if you want to place it
into a folder select this via
!
and . If there is already an Assign file with the same
name on disk which you don’t want to overwrite (= erease while overwriting) just press
and give a new name (see page17).
%
With
you leave the function.
&
We strongly recommend to save a backup copy of the Assign file under a different name
from time to time – a story has been told of someone who deleted his 3000 Song Assign
file by saving an empty one with the same name ...
File Assignment
TMR LOA MER SAV PTH ASG MOV CLR
#
##
#
File Assignment
TMR LOA MER SAV PTH ASG MOV CLR
#
##
#