Millipore Simplicity system User Manual

Simplicity® system
Simplicity UV system
User manual

Millipore Simplicity system Specifications

General

TOC	< 5 ppb
Filtration Technology	Ultrafiltration
Type of Water Produced	Ultrapure Type 1 Water
Resistivity	18.2 MΩ·cm
Bacteria	<1 CFU/mL
Power Supply	100-240 V AC, 50-60 Hz

Summary

Introduction

Using this Manual

Guide for installation, operation, and maintenance of the Simplicity or Simplicity UV Water Purification System.

Safety Information

Instructions on operating the Simplicity System according to manual specifications and safety precautions.

Introduction

Contacting Millipore® SAS

Information on how to contact Millipore SAS via Internet and manufacturing site address.

Product Information

Simplicity System Overview

Visual overview of the Simplicity system, highlighting the DISPLAY and KEYPAD.

Simplicity System Product Water Specifications

Details of water flow rate and quality specifications for the Simplicity system.

Product Information

Schematic of Main Components

Diagram illustrating the main components of the Simplicity water purification system.

Operating principle

Explanation of how the Simplicity Water Purification System functions with its components.

Product Information

Technical Specifications

Detailed specifications including dimensions, weight, noise level, and electrical requirements.

Pre Installation

Installation Requirements

Specifies the requirements for pretreated water and environmental conditions for installation.

Optional Equipment You May Need

Information about optional equipment like the Wall Mounting Bracket and its catalogue number.

Unpacking the Simplicity System– What's Inside?

Instructions on how to unpack the system and check its contents using a checklist.

Installation

Preparation of the System

Steps for preparing the system, including removing protective foam from the UV lamp cable.

Filling the Internal Tank

Detailed instructions on how to remove, fill, and re-install the internal water tank.

Installation

Installation of the Tank Vent Filter

Steps for installing the Vent Filter into the tank lid.

Installation

Connection of the Power Cord – Turning on the System Power

Guide on connecting the power cord and powering on the system.

Start-up Displays

Description of the displays shown when the system is powered on.

Installation

Installation of the SimpliPak cartridge

Instructions for installing the SimpliPak cartridge, including precautions regarding the UV Lamp.

Installation

Install the SimpliPak

Visual guide showing how to fully seat the SimpliPak into the system ports.

Installation

Installation of the Tygon® Tubing

Steps for installing the Tygon tubing and barbed fitting onto the POU dispenser.

Installation

Purging Air from the System

Procedure for purging trapped air from the system after installing components.

Hydrating the System

Steps for hydrating the system, including overnight recirculation for media rinsing.

Installation

Installation and Rinsing of the Final Filter

Instructions for installing and rinsing the final filter before use.

Installation

How to Show Resistivity or Conductivity Units (C01)

Guide on how to display resistivity or conductivity units on the system display.

Installation

How to Set the Resistivity Setpoint (CO2)

Procedure for setting the resistivity setpoint to monitor low product resistivity.

Using the Simplicity System

Understanding the Display

Explanation of the system display, including operating modes, parameters, and alarms.

How to Get Water from the Simplicity System

Instructions on how to dispense water using the system keypad.

Maintaining a minimum level of water in the tank

Guidance on refilling the water tank when the level is low to ensure continuous operation.

Using the Simplicity System

Operating Modes

Description of different operating modes like Standby, Pre Operate, and Dispensing.

Using the Simplicity System

How to view the Product Resistivity and Temperature in Pre Operate mode

Method to view water quality parameters like resistivity and temperature in Pre Operate mode.

How to recirculate water manually before dispensing

Procedure to manually recirculate water to improve quality before dispensing.

Using the Simplicity System

How to Understand Simplicity system messages

Explanation of system messages, including Pack Alarm and UV Lamp Alarm, for user awareness.

Maintenance

Maintenance Schedule

Overview of scheduled maintenance tasks and when they should be performed.

Maintenance

How to Replace the SimpliPak cartridge

Step-by-step guide on how to remove the SimpliPak cartridge from the system.

Maintenance

Install the new SimpliPak cartridge

Instructions for installing a new SimpliPak cartridge, including O-ring preparation.

Maintenance

Install the Barbed Fitting and Tygon Tubing (G)

Re-installing the barbed fitting and Tygon tubing after cartridge replacement.

Purging Air from the System

Instructions for purging air from the system after performing maintenance.

Hydrating the System

Steps for hydrating the system after maintenance procedures.

Replacing the Final Filter

Reference to the section detailing the procedure for replacing the Final Filter.

Maintenance

How to Replace the Final Filter

Detailed steps for removing the used Final Filter and installing a new one.

Maintenance

How to Calibrate the Tank Level (C03)

Procedure to calibrate the tank level display for accurate readings.

Maintenance

How to Replace the UV Lamp (UV System only)

Steps for removing the UV Lamp from the system when replacement is due.

Maintenance

Removing the UV Lamp

Detailed instructions for safely removing the UV Lamp from its housing.

Maintenance

Installing the new UV Lamp

Steps for installing a new UV Lamp, including electrical connection and component reassembly.

Maintenance

How to View or Reset the UV Lamp Timer (C04)

Guide on viewing the remaining days on the UV Lamp Timer.

Maintenance

How to Reset the UV Lamp Timer

Procedure for resetting the UV Lamp Timer after a new UV Lamp has been installed.

Troubleshooting

The Display screen is blank.

Troubleshooting steps for a blank display screen, checking power and fuses.

Low water flow or no water flow when the Main Button is pressed (DISPENSING mode).

Solutions for low or no water flow issues, checking tank level, installation, and filters.

The last Product resistivity value is not displayed when you press the "-" Button in PRE OPERATE mode.

Troubleshooting for missing resistivity values, checking measurement conditions and cartridge.

Troubleshooting

System standby or low resistivity issues.

Troubleshooting for system standby or low resistivity readings, suggesting recirculation or cartridge replacement.

The UV Timer is exhausted.

Actions to take when the UV Timer indicates exhaustion, requiring lamp replacement and timer reset.

The UV Lamp is not installed correctly or not installed at all.

Steps for addressing incorrect UV Lamp installation, recommending power off and reinstallation.

Ordering Information

Catalogue Numbers for Simplicity Systems

Provides catalogue numbers for Simplicity system models based on voltage.

Catalogue Numbers for Consumables

Lists catalogue numbers for various consumable items such as cartridges and filters.

Catalogue Numbers for Accessories

Lists catalogue numbers for system accessories like the Wall Mounting Bracket.

Quick access to most common procedures

Contacting Millipore® SAS

Provides contact information for Millipore SAS.

How to recirculate water manually before dispensing

Guide on manually recirculating water to improve quality before dispensing.

How to Replace the Final Filter

Steps for replacing the Final Filter.

How to Replace the UV Lamp (UV System only)

Instructions for replacing the UV Lamp.

How to Replace the SimpliPak cartridge

Steps for replacing the SimpliPak cartridge.