Need help?Do you have a question about the Millipore Simplicity system and is the answer not in the manual?
Guide for installation, operation, and maintenance of the Simplicity or Simplicity UV Water Purification System.
Instructions on operating the Simplicity System according to manual specifications and safety precautions.
Information on how to contact Millipore SAS via Internet and manufacturing site address.
Visual overview of the Simplicity system, highlighting the DISPLAY and KEYPAD.
Details of water flow rate and quality specifications for the Simplicity system.
Diagram illustrating the main components of the Simplicity water purification system.
Explanation of how the Simplicity Water Purification System functions with its components.
Detailed specifications including dimensions, weight, noise level, and electrical requirements.
Specifies the requirements for pretreated water and environmental conditions for installation.
Information about optional equipment like the Wall Mounting Bracket and its catalogue number.
Instructions on how to unpack the system and check its contents using a checklist.
Steps for preparing the system, including removing protective foam from the UV lamp cable.
Detailed instructions on how to remove, fill, and re-install the internal water tank.
Steps for installing the Vent Filter into the tank lid.
Guide on connecting the power cord and powering on the system.
Description of the displays shown when the system is powered on.
Instructions for installing the SimpliPak cartridge, including precautions regarding the UV Lamp.
Visual guide showing how to fully seat the SimpliPak into the system ports.
Steps for installing the Tygon tubing and barbed fitting onto the POU dispenser.
Procedure for purging trapped air from the system after installing components.
Steps for hydrating the system, including overnight recirculation for media rinsing.
Instructions for installing and rinsing the final filter before use.
Guide on how to display resistivity or conductivity units on the system display.
Procedure for setting the resistivity setpoint to monitor low product resistivity.
Explanation of the system display, including operating modes, parameters, and alarms.
Instructions on how to dispense water using the system keypad.
Guidance on refilling the water tank when the level is low to ensure continuous operation.
Description of different operating modes like Standby, Pre Operate, and Dispensing.
Method to view water quality parameters like resistivity and temperature in Pre Operate mode.
Procedure to manually recirculate water to improve quality before dispensing.
Explanation of system messages, including Pack Alarm and UV Lamp Alarm, for user awareness.
Overview of scheduled maintenance tasks and when they should be performed.
Step-by-step guide on how to remove the SimpliPak cartridge from the system.
Instructions for installing a new SimpliPak cartridge, including O-ring preparation.
Re-installing the barbed fitting and Tygon tubing after cartridge replacement.
Instructions for purging air from the system after performing maintenance.
Steps for hydrating the system after maintenance procedures.
Reference to the section detailing the procedure for replacing the Final Filter.
Detailed steps for removing the used Final Filter and installing a new one.
Procedure to calibrate the tank level display for accurate readings.
Steps for removing the UV Lamp from the system when replacement is due.
Detailed instructions for safely removing the UV Lamp from its housing.
Steps for installing a new UV Lamp, including electrical connection and component reassembly.
Guide on viewing the remaining days on the UV Lamp Timer.
Procedure for resetting the UV Lamp Timer after a new UV Lamp has been installed.
Troubleshooting steps for a blank display screen, checking power and fuses.
Solutions for low or no water flow issues, checking tank level, installation, and filters.
Troubleshooting for missing resistivity values, checking measurement conditions and cartridge.
Troubleshooting for system standby or low resistivity readings, suggesting recirculation or cartridge replacement.
Actions to take when the UV Timer indicates exhaustion, requiring lamp replacement and timer reset.
Steps for addressing incorrect UV Lamp installation, recommending power off and reinstallation.
Provides catalogue numbers for Simplicity system models based on voltage.
Lists catalogue numbers for various consumable items such as cartridges and filters.
Lists catalogue numbers for system accessories like the Wall Mounting Bracket.
Provides contact information for Millipore SAS.
Guide on manually recirculating water to improve quality before dispensing.
Steps for replacing the Final Filter.
Instructions for replacing the UV Lamp.
Steps for replacing the SimpliPak cartridge.
General| Brand | Millipore |
|---|---|
| Model | Simplicity system |
| Category | Water Filtration Systems |
| Language | English |
To Next Page