MIMAKI TS300P-1800 - Nozzle Recovery Function

4-13
1
2
2
4
5
6
Chapter 4 Maintenance
Nozzle Recovery Function
NOZZLE RECOVERY: When nozzles missing can not be
improved at specific points, other good nozzles can be
used as alternatives for printing.
1
Press
(MENU)
in LOCAL.
• MAINTENANCE MENU will be displayed.
2
Press to select “NOZZLE
RECOVERY”, and press the key.
3
Press the key twice.
• Printing of the nozzle pattern will start.
• Select “ENTRY” then “Move to select of the
Nozzle line (Step 4) without drawing a pattern”
4
Select the Nozzle line that needs NOZZLE
RECOVERY by pressing , and
press the key.
5
Register the Nozzle number that needs
NOZZLE RECOVERY and press the
key.
(1) Select the registration number from 1 to 10
by pressing [][] and press the [ENTER]
key.
(2) Register the nozzle number that needs
recovery by pressing [][] and press the
[ENTER] key.
6
Press the key several times to
end the setting.
1
10
21
30
41
50
61
70
81
90
101
110
121
130
141
150
161
170
181
190
201
210
221
230
1
10
21
30
41
50
61
70
81
90
101
110
121
130
141
150
161
170
181
190
201
210
221
230
1
10
21
30
41
50
61
70
81
90
101
110
121
130
141
150
161
170
181
190
201
210
221
230
1
10
21
30
41
50
61
70
81
90
101
110
121
130
141
150
161
170
181
190
201
210
221
230
1
10
21
30
41
50
61
70
81
90
101
110
121
130
141
150
161
170
181
190
201
210
221
230
1
10
21
30
41
50
61
70
81
90
101
110
121
130
141
150
161
170
181
190
201
210
221
230
1
10
21
30
41
50
61
70
81
90
101
110
121
130
141
150
161
170
181
190
201
210
221
230
1
10
21
30
41
50
61
70
81
90
101
110
121
130
141
150
161
170
181
190
201
210
221
230
241
250
261
270
281
290
301
310
241
250
261
270
281
290
301
310
241
250
261
270
281
290
301
310
241
250
261
270
281
290
301
310
241
250
261
270
281
290
301
310
241
250
261
270
281
290
301
310
241
250
261
270
281
290
301
310
241
250
261
270
281
290
301
310
H3 H4
Overhead view
H1-AB H2-CD H3-AB H4-AB
Nozzle line
H1-CD H2-AB H3-CD H4-CD
• When using leaf media, set a media of more than
A3 size put horizontally. If a media with narrow
width is set, printing will only be conducted to
midway.
Nozzle pattern of Head 1
SELECT ENTRY NOZZLE
H1-AB
>
> H1-CD
>
H2-AB
>
H2-CD
>><<
>
＊＊＊＊
Head No.
(H1 to H4)
Nozzle
line
• Up to 10 nozzles can be registered per 1 nozzle
line.
• Even if you use this function, time required for
drawing does not change.
• When printing has been done with the lowest path,
nozzle recovery is not reflected.
Head1-AB
No.1
No.2
16
128
No.3
184
No.4
OFF
No.5
OFF
>><<
Recovery nozzle No. or OFF
Registration number : 1 to 10
1
10
21
30
41
50
61
70
81
90
101
110
121
130
141
150
161
170
181
190
201
210
221
230
Nozzle missing
No.184
Nozzle number
Nozzle missing No.16
Nozzle missing
No.128
Registration
number
Recovery
Nozzle No.
State
1 16 Target for nozzle recovery
2 128 Target for nozzle recovery
3 184 Target for nozzle recovery
4 OFF No registration
5 OFF No registration
Example of nozzle to be recovered