What does 'Unknown Device' mean on Mortara Medical Equipment?
If the system displays “Unknown Device” or “Unknown Manufacturer”, the TRPC or EPC is not recognized due to an incorrect installation or lack of installation of the device driver. Note that TRPC or EPC is not compatible with X-Scribe V3.10. You will need an MMM device and drivers.
How to fix treadmill belt slippage on Mortara Medical Equipment?
If the treadmill belt starts to slip, it could be due to looseness that allows it to shift. To resolve this, tighten the adjustment bolts on both sides until the slippage stops.
What to do if there is no signal onscreen on Mortara X-Scribe Medical Equipment?
If there is no signal onscreen (wireless option) with the patient connected (or with a simulator), and only the squared waveform/lead fail indicator appears, check that X-Scribe and the digital transmitter work on the same channel. Refer to the transmitter user manual to check and change the channel. Refer to Settings in this manual to set the receiving channel for X-Scribe.
How to troubleshoot packet errors on Mortara Medical Equipment?
If you are experiencing packet errors or signal drop (wireless option), and the signal onscreen shows artifact even when tested with a simulator, check that no medical equipment is operating at the same frequency in proximity to the system. Run the built-in spectrum analyzer to locate the source of the interference and to set the proper channel on the digital transmitter.
What to do if Mortara X-Scribe Medical Equipment menu cursor won't move?
If the menu cursor will not move, the mouse cable may be disconnected or the keyboard/mouse cables may be transposed. Turn the system OFF and check the mouse port connections.
Why is my Mortara X-Scribe keyboard not responding?
If there is no response to keyboard commands, the keyboard cable may be disconnected or the keyboard/mouse cables may be transposed. Turn the system OFF and check the keyboard to mouse port connections.
Why is my Mortara Medical Equipment Z-fold printer not working?
If the Z-fold writer paper is out, the light on the Z-fold writer is on, and it's not printing or printing ECGs/reports unevenly, it could be due to a paper jam, no paper in the tray, an open writer door, or a printer head that needs cleaning. Open the writer cover and remove any jammed paper. Insert a new packet of paper in the tray. Make sure the writer door is latched. Refer to printer head cleaning instructions in Appendix F.
What to do for ECG Front-End Error on Mortara X-Scribe?
If the ECG Front-End Error occurs, and you can’t proceed, it could be that the MMM device is not correctly connected or that there are incorrect Power Savings settings. Try disconnecting the USB cable from the PC and then reconnecting it. The system should emit a confirmation beep. If rebooting fixes the problem, the system likely has incorrect Power Saving settings. To correct this: 1. Close the X-Scribe application. 2. Select “Start”, “Settings”, then “Control Panel”. 3. Double click on “Power Management” icon. 4. If displayed, set “Stand-by” setting to “Never”. 5. Click OK and close all open Windows. 6. Reboot system.
How to correct baseline drift on Mortara Medical Equipment?
Baseline drift can be caused by poor skin-to-electrode contact. Re-prep the skin and replace the faulty electrode to resolve this issue.
How to reduce muscle noise in Mortara Medical Equipment readings?
Muscle noise can occur if the electrode is placed over muscle or fatty tissue. To fix this, find a stable electrode site, re-prep the skin, and apply a new electrode.
Defines symbols for warnings, cautions, and notes to ensure safe operation.
Provides essential safety guidelines for operating the device.
Ensures electrical safety and patient protection during use.
Highlights hazards like defibrillation, flammable anesthetics, and improper use.
Outlines the manual's scope and intended reader.
Defines the device's purpose and when it should be used.
Details the X-Scribe system, its features, and included parts.
Lists the technical specifications of the X-Scribe system.
Step-by-step guide for assembling and installing the X-Scribe system.
Visual guide to system connections and details on the isolation transformer.
Instructions for powering on and launching the X-Scribe software.
Overview of the X-Scribe's functions and features.
Explanation of the graphical user interface and on-screen data.
Details the use of function keys for system control.
Steps for preparing the patient and attaching electrodes.
Guides on applying filters like SCF, AC, and 40 Hz.
Details on test phases: Pre-Exercise, Exercise, Recovery, and Final Report.
Procedures for managing, printing, and archiving test reports.
Configuring AC frequency, RF channels, and performing RF scans.
Creating, modifying, and selecting user profiles and exercise protocols.
Setting up network data export/import and standard user configurations.
Guidelines for regular equipment cleaning and upkeep.
Diagnosing issues and recording system details for service.
General| Brand | Mortara |
|---|---|
| Model | X-Scribe |
| Category | Medical Equipment |
| Language | English |
To Next Page
