Nordson Asymtek Spectrum S-920

Table of Contents xi
Table of Figures
Figure 1-1 Front View...........................................................................................................................1-8
Figure 1-2 Front View (Open Dispensing Area - Dual Conveyors)...................................................... 1-9
Figure 1-3 Dispensing Area ...............................................................................................................1-10
Figure 1-4 Service Station..................................................................................................................1-11
Figure 1-5 Front Panel .......................................................................................................................1-12
Figure 1-6 Front Cabinet (Dual Conveyor System shown) ................................................................1-13
Figure 1-7 Rear View .........................................................................................................................1-15
Figure 1-8 Rear View Open ...............................................................................................................1-16
Figure 1-9 Rear Cabinet (Dual Conveyor Configuration Shown).......................................................1-17
Figure 1-10 Rear Panel Connections...................................................................................................1-18
Figure 2-1 Safety Warning Labels (Front Cover) .................................................................................2-7
Figure 2-2 Safety Warning Labels (Front Inside Panel)....................................................................... 2-7
Figure 2-3 Safety Warning Labels (Dispensing Area) .........................................................................2-8
Figure 2-4 Safety Warning Labels (Conveyor).....................................................................................2-9
Figure 2-5 Safety Warning Labels (Rear)) ...........................................................................................2-9
Figure 2-6 Safety Warning Labels - Power Manager.........................................................................2-10
Figure 2-7 Laser Height Sensor .........................................................................................................2-11
Figure 2-8 EMO/Main Circuit Breaker Locations ...............................................................................2-12
Figure 2-9 Interlock Active Message..................................................................................................2-13
Figure 2-10 Clear Interlock Message...................................................................................................2-13
Figure 2-11 Electrical/Pneumatical Lockout/Tagout ............................................................................2-15
Figure 3-1 Removing the Shipping Brackets .......................................................................................3-2
Figure 3-2 Adjusting the Levelers ........................................................................................................3-3
Figure 3-3 Dispensing Head Stopper Locations .................................................................................. 3-5
Figure 3-4 Removing the Z-Head Bracket ...........................................................................................3-5
Figure 3-5 Removing the Service Station Packing Tape .....................................................................3-6
Figure 3-6 Removing the Front Cover .................................................................................................3-6
Figure 3-7 S-920 Dispensing System Scale Stem............................................................................... 3-7
Figure 3-8 Leveling the Dispensing System – X-Axis..........................................................................3-8
Figure 3-9 Dispensing System Levelers (Feet)....................................................................................3-8
Figure 3-10 Leveling the Dispensing System – Y-Axis.......................................................................... 3-9
Figure 3-11 Leveling the Scale ............................................................................................................3-10
Figure 3-12 Replacing the Scale Cover ...............................................................................................3-10
Figure 3-13 Setting up the Weigh Station ............................................................................................3-11
Figure 3-14 Purge Station ....................................................................................................................3-11
Figure 3-15 Installing the Light Beacon ...............................................................................................3-12
Figure 3-16 Windows Explorer - FmXP Directory ................................................................................3-13
Figure 3-17 Dispensing System Serial Number Label .........................................................................3-13
Figure 3-18 Aligning the Laptop Computer to the Tray........................................................................3-14
Figure 3-19 Camera (Rear View) .........................................................................................................3-15
Figure 3-20 Anchoring the Dispensing System....................................................................................3-16
Figure 4-1 Main Power Circuit Breaker and Cable ..............................................................................4-2
Figure 4-2 Connecting the Power and Air Supply.....................................................................................4-3
Figure 4-3 FmXP Message 30416 .......................................................................................................4-5
Figure 4-4 FmXP Main Window ...........................................................................................................4-5
Figure 4-5 Setup Conveyor Window ....................................................................................................4-6
Figure 4-6 FmXP - Setup Configuration - Conveyor............................................................................4-7
Figure 4-7 FmXP Scale Setup .............................................................................................................4-8
Figure 4-8 FmXP - Setup Vision ..........................................................................................................4-9
Figure 4-9 Air Regulator and Gauge Locations .................................................................................4-13
Figure 4-10 Dispenser I/O (Outputs 32-63) .........................................................................................4-14
Figure 4-11 Conveyor Jog Commands Dialog Box.............................................................................. 4-16
Figure 4-12 SMEMA Connections........................................................................................................4-18