Omron CP - PROGRAMMING MANUAL 05-2007 - Page 1167

1134
Index
SEND(090), 844
SET
, 122
SETA(530), 124, 127, 130
SETB(532), 127
SETR(635)
, 580
SIGN(600), 398
SIN(460), 495, 547
SIND(851)
, 547
Single-precision Floating-point Input Comparison In-
structions (329 to 334)
, 512
SINS(641), 609
SNUM(638), 600
SNXT(009)
, 752
SPED(885), 723
SQRT(466), 505, 557
SQRTD(857)
, 557
SRCH(181), 584
SREAD(639), 603
SSET(630)
, 567
STEP(008), 752
STUP(237), 841
SUM(184)
, 594
SWAP(637), 586, 600, 603, 606, 609, 612
SWRIT(640), 606
TAN(462)
, 498
TAND(853), 550
TCMP(085), 233
testing bit status
, 110
TIM, 170
TIMH(015)
, 174
TIMHWX(817), 1001
TIMHX(551), 174
TIML(542)
, 184
TIMLX(553), 184
TIMW(813), 995
TIMWX(816)
, 995
TIMX(550), 170
TKOF(821), 1043
TKON(820)
, 1040
TMHH(540), 178
TMHHX(552), 178
TMHW(815)
, 1001
TOCV(285), 971
TRSM(045), 932
TST(350)
, 110
TSTN(351), 110
TTIM(087), 181
TTIMX(555)
, 181
TXD(236), 815
UP(521), 109
WDT(094)
, 962
XCGL(562), 265
XCHG$(665)
, 1029
XCHG(073)
, 264
XFER(070), 260
XFRB(062), 257
XNRL(613)
, 447
XNRW(037), 445
XORL(612), 444
XORW(036)
, 442
ZCP(088), 242
ZCPL(116), 244
ZONE(682)
, 642
instructions
, 77, 208
Basic I/O Unit instructions, 769, 800
basic instructions, 4
block programming instructions
, 975, 1007
block programs, 40
clock instructions, 918, 974
comparison instructions
, 209, 241
controlling execution conditions
UP(521) and DOWN(522), 109
controlling high-speed counters and pulse outputs
, 705
controlling tasks, 58
conversion instructions, 389, 430
counter instructions
, 168, 208
data control instructions, 615, 667
data movement instructions, 247
data shift instructions
, 274, 319
debugging instructions, 932, 935
decrement instructions
, 320, 336
differentiated instructions, 19
display instructions, 911, 913
execution conditions
, 17
failure diagnosis instructions, 936, 960
floating-point math instructions, 472, 512, 525, 563
high-speed counter instructions
, 705
increment instructions, 320, 336
input and output instructions
, 4, 6
input comparison instructions
, 209, 215, 512, 563
input differentiation, 17
instruction conditions, 5
interrupt control instructions
, 692
listed by function code, 1099
logic instructions, 436, 451
loops
, 5, 38
network instructions, 844
operands, 5
programming locations
, 6
pulse output instructions, 705
restrictions in tasks, 61
sequence control instructions
, 132, 167
sequence input instructions, 89, 113
sequence output instructions, 113, 127