xvii
Related Manuals
The following manuals are used for the CP-series CPU Units. Refer to these manuals as required.
Cat. No. Model numbers Manual name Description
W451 CP1H-X40D@-@
CP1H-XA40D@-@
CP1H-Y20DT-D
CP1L-L14D@-@
CP1L-L20D@-@
CP1L-M30D@-@
CP1L-M40D@-@
SYSMAC CP Series
CP1H and CP1L CPU
Unit Programming
Manual
(This manual)
Provides the following information on the CP Series:
• Programming instructions
• Programming methods
•Tasks
• File memory
• Functions
Use this manual together with the CP Series CP1H
CPU Units Operation Manual (W450) and CP
Series CP1L CPU Units Operation Manual (W462)
W450 CP1H-X40D@-@
CP1H-XA40D@-@
CP1H-Y20DT-D
SYSMAC CP Series
CP1H CPU Unit
Operation Manual
Provide the following information on the CP Series:
• Overview, design, installation, maintenance, and
other basic specifications
•Features
• System configuration
• Mounting and wiring
• I/O memory allocation
• Troubleshooting
Use this manual together with the CP1H Program-
mable Controllers Programming Manual (W451).
W462 CP1L-L14D@-@
CP1L-L20D@-@
CP1L-M30D@-@
CP1L-M40D@-@
SYSMAC CP Series
CP1L CPU Unit Oper-
ation Manual
W461 CP1L-L14D@-@
CP1L-L20D@-@
CP1L-M30D@-@
CP1L-M40D@-@
SYSMAC CP Series
CP1L Introduction
Manual
Provides basic setup information for CP1L PLCs,
including the following.
• Basic configuration and part names
• Mounting and wiring procedures
• Programming, program transfer, and debugging
with the CX-Programmer
• Application programming examples using the
CP1L
W342 CS1G/H-CPU@@H
CS1G/H-CPU@@-V1
CS1D-CPU@@H
CS1D-CPU@@S
CS1W-SCU21
CS1W-SCB21-V1/41-V1
CJ1G/H-CPU@@H
CJ1G-CPU@@P
CP1H-CPU@@
CJ1G-CPU@@
CJ1W-SCU21-V1/41-V1
SYSMAC CS/CJ-
series Communica-
tions Commands Ref-
erence Manual
Describes commands addressed to CS-series, and
CJ-series CPU Units, including C-mode commands
and FINS commands.
Note This manual describes on commands
address to CPU Units regardless of the com-
munications path. (CPU Unit serial ports,
Serial Communications Unit/Board ports, and
Communications Unit ports can be used.)
Refer to the relevant operation manuals for
information on commands addresses to Spe-
cial I/O Units and CPU Bus Units.
W446 WS02-CXPC1-E-V70 SYSMAC CX-Pro-
grammer
Ver. 7.0 Operation
Manual
Provides information on installing and operating the
CX-Programmer for all functions except for function
blocks.
W447 WS02-CXPC1-E-V70 SYSMAC CX-Pro-
grammer Ver. 7.0
Operation Manual
Function Blocks
Provides specifications and operating procedures
for function blocks. Function blocks can be used
with CX-Programmer Ver. 6.1 or higher and either a
CS1-H/CJ1-H CPU Unit with a unit version of 3.0 or
a CP1H CPU Unit. Refer to W446 for operating pro-
cedures for functions other than function blocks.
W444 CXONE-AL@@C-E CX-One FA Inte-
grated Tool Package
Setup Manual
Provides an overview of the CX-One FA Integrated
Tool and installation procedures.
To Next Page
Loading...
