Oriental motor BLH Series - Page 143

143
Information
bit Information
Information bit
output signal
Cause Condition to reset and clear
20 Tripmeter
*4
INFO-TRIP
Total rotation amount inside the driver
(tripmeter) increased to the value set in the
"Tripmeter information" parameter or more.
One of the following operations was
performed, and total rotation amount inside
the driver (tripmeter) fell below the value set
in the "Tripmeter information" parameter.
•
The "Tripmeter information" parameter
was set again.
•
"Clear tripmeter" was executed with the
MEXE02
.
•
"Clear tripmeter" was executed via RS-485
communication.
21 Odometer
*5
INFO-ODO
The cumulative rotation amount inside the
driver (odometer) increased to the value set
in the "Odometer information" parameter or
more.
The "Odometer information" parameter
was set again, and the cumulative rotation
amount inside the driver (odometer) fell
below the value set in the "Odometer
information" parameter.
24
Torque limiting value
setting error
INFO-TRQ-DE
The data exceeding the torque limiting
value set in the "Torque limiting maximum
value" parameter is set.
•
The torque limiting value having set was
set again so that it was lower than the
value set in the "Torque limiting maximum
value" parameter.
•
The value set in the "Torque limiting
maximum value" parameter was set
again so that it was larger than the torque
limiting value having set.
25
Rotation speed setting
error
INFO-SPD-DE
Data larger than the rotation speed in
the "Speed upper limit" parameter or
smaller than that in the "Speed lower limit"
parameter is set.
•
The rotation speed below the value set in
the "Speed upper limit" parameter was set
again. Or the rotation speed exceeding
the value set in the "Speed lower limit"
parameter was set again.
•
The value exceeding the motor rotation
speed was set in the "Speed upper limit"
parameter again. Or the value below
the motor rotation speed was set in the
"Speed lower limit" parameter again.
26 Main power supply time INFO-PTIME
A time period having supplied the power
to the main power supply of the driver
increased to the value set in the "Main
power supply time information" parameter
or more.
The "Main power supply time information"
parameter was set again, and the time
period having supplied the power to the
main power supply of the driver fell below
the value set in the "Main power supply time
information" parameter.
27 Main power count INFO-PCOUNT
The number of times to turn on the main
power supply of the driver increased to the
value set in the "Main power supply count
information" parameter or more.
The "Main power supply count information"
parameter was set again, and the number
of times to turn on the main power supply
of the driver fell below the value set in the
"Main power supply count information"
parameter.
28
Operation start limit
mode
INFO-DSLMTD
•
"Teaching/remote operation" was
executed.
•
"Conguration" was executed.
•
"Data writing" was executed with the
MEXE02
.
•
"Restored to the factory setting" was
executed.
•
"Teaching/remote operation" was
complete.
•
"Conguration" was complete.
•
"Data writing" with the
MEXE02
was
complete.
•
"Restored to the factory setting" was
complete.
29 I/O test mode INFO-IOTEST
•
"I/O test" was executed.
•
"Conguration" was executed.
•
"I/O test" was complete.
•
"Conguration" was complete.
30 Conguration request INFO-CFG
A parameter that required "Conguration"
was changed.
(Update timing: C)
"Conguration" was executed.
31 Power cycling request INFO-RBT
A parameter that required to turn on the
driver power again was changed.
(Update timing: D)
The driver power was turned on again.
*4
The tripmeter is saved in the non-volatile memory in the driver at intervals of one minute. If the power supply is turned o before
saving in the driver, the rotation amount for one minute is not applied.
*5
The odometer is saved in the non-volatile memory in the driver at intervals of one minute. If the power supply is turned o before
saving in the driver, the rotation amount for one minute is not applied.