pellenc 200 - Pruning Shears Battery Level 2 Message Sheet

To Next Page

To Previous Page

"- LEVEL EXPERT- PELLENC POWER TOOL BATTERY" Workshop document

Issue 11/2016 ref. : DOCUMENT ATELIER_BATTERIE_EXP_OUTILS_PELLENC_V2_2016_ENG

At the end of the Level 2 diagnostic, the battery switches

to storage mode (discharge to 45%).

Press switch to cancel the discharge: «I» then «0»

6SHFL¿FWR/L[LRQ

BATTERY DIAGNOSTIC WITHOUT SOFTWARE

VEL 3 - PELLENC AUTHORISED REPAIRER

Fault No.

ÀDVKLQJ

Type of battery Explanation of the messages displayed

Voltage of the weakest cell in mVolts

Voltage of the strongest cell in mVolts

Start of charge with a cell under 2.5 V

Charger fault

End of charging with excessive difference between cells

See message 15.

Temperature below 0°C during charging

Temperature above 60°C during use

Temperature above 45°C during charging

End of charge with a cell above 4.23 V

Charging stopped with a cell above 4.5V

Complete discharge of the battery in use

Temp. diff. of more than 10°C between the 2 sensors

Fault on balancing resistor and No. concerned

Software version of pruning shears and battery

Excessive current in the motor control MOSs

200 Excessive voltage on power supply

200 ,QVXI¿FLHQWYROWDJHRQSRZHUVXSSO\

Excessive temperature on motor MOSs

Fault on trigger sensor line. The LiXion must be recognized when the battery is started.

200 Fault on the motor line

Pruning shears software version.

Power consumption from start-up

Number of hours switched on since entry into service

Number of hours switched on since last overhaul

150P / 200/250 Excessive current in the motor control MOSs

150P / 200/250 Excessive voltage on power supply

150P / 200/250 ,QVXI¿FLHQWYROWDJHRQSRZHUVXSSO\

150P / 200/250 Excessive temperature on motor MOSs

150P / 200/250 Fault on trigger sensor line. Or no shears connected.

150P / 200/250 Fault on the motor line

BATTERY

End of charging with excessive difference between cellsEnd of charging with excessive difference between cells

See message 15.See message 15.

Temperature below 0°C during chargingTemperature below 0°C during charging

Temperature above 60°C during useTemperature above 60°C during use

Temperature above 45°C during chargingTemperature above 45°C during charging

End of charge with a cell above 4.23 VEnd of charge with a cell above 4.23 V

PRUNING

Temperature above 60°C during use

Temperature above 45°C during chargingTemperature above 45°C during charging

End of charge with a cell above 4.23 VEnd of charge with a cell above 4.23 V

Charging stopped with a cell above 4.5VCharging stopped with a cell above 4.5V

Complete discharge of the battery in useComplete discharge of the battery in use

Temp. diff. of more than 10°C between the 2 sensorsTemp. diff. of more than 10°C between the 2 sensors

Fault on balancing resistor and No. concernedFault on balancing resistor and No. concerned

Software version of pruning shears and batterySoftwa

SHEARS

Temp. diff. of more than 10°C between the 2 sensorsTemp. diff. of more than 10°C between the 2 sensors

Fault on balancing resistor and No. concernedFault on balancing resistor and No. concerned

Software version of pruning shears and batteryn of pruning shears and battery

ve current in the motor control MOSs

Excessive voltage on power supply

,QVXI¿FLHQWYROWDJHRQSRZHUVXSSO\

Excessive temperature on motor MOSs

Fault on trigger sensor line. The LiXion must be recognized when the battery is started.

PRUNING SHEARS BATTERY LEVEL 2 MESSAGE SHEET

7UHHOLRQ VSHFL¿F EDW-

teries 150 / 150P / 250.

Main Page

pellenc 200 - Pruning Shears Battery Level 2 Message Sheet

Table of Contents

Related product manuals