Pentair AK110 - Page 51

51
p
H, Mix TMR00:00:00
>TD00:00:00 CNT: 0 S 00:00:00 STS:OFF TOT 0:00
Timer Screen, Relay 1 (pH)
P
ager4 TMR00:00:00
>TD00:00:00 CNT: 0 S 00:00:00 STS:OFF TOT 0:00
Timer Screen, Pager / E-mail 4
P
ager3 TMR00:00:00
>TD00:00:00 CNT: 0 S 00:00:00 STS:OFF TOT 0:00
Timer Screen, Pager / E-mail 3 Timer Screen, Pager / E-mail 2
P
ager2 TMR00:00:00
>TD00:00:00 CNT: 0 S 00:00:00 STS:OFF TOT 0:00
Timer Screen, Pager / E-mail 1
P
ager1 TMR00:00:00
>TD00:00:00 CNT: 0 S 00:00:00 STS:OFF TOT 0:00 Alarm TMR00:00:00 >TD00:00:00 CNT: 0 S 00:00:00 STS:OFF TOT 0:00
Timer Screen, Alarm
Relay3 TMR00:00:00 >TD00:00:00 CNT: 0 S 00:00:00 STS:OFF TOT 0:00
Timer Screen, Relay 3 (Optional)
AK110 Relay and Alarm Timer Screen Navigation
pH > 7.67-OFF 7.50s
ORP 490 -OFF 700s _____ 69.0f SW1OFFSW2OFF
Main Status, cursor at pH value Main Status, pH Relay Status
pH 7.67>OFF 7.50s ORP 490 -OFF 700s _____ 69.0f SW1OFFSW2OFF
Main Status, ORP Relay Status
pH 7.67-OFF 7.50s ORP 490 >OFF 700s _____ 69.0f SW1OFFSW2OFF
Back
p
H, Mix TMR00:00:00
>TD00:00:00
CNT: 0 S 00:00:00 STS:OFF TOT 0:00
Timer Screen, pH Relay
O
RP, Mix TMR00:00:00
>TD00:00:00
CNT: 0 S 00:00:00 STS:OFF TOT 0:00
Timer Screen, Relay 2 (ORP)
8 7 6
5 4 3 2 1
pH, Mix TMR00:09:01 >TD00:23:45
CNT: 1234 S 02:34:56 STS:OFF TOT 12:34
Timer Screen, Today (TD)
pH, Mix TMR00:09:01 TD00:23:45 CNT:>1234 S 02:34:56
STS:OFF TOT 12:34
Timer Screen, Count (CNT)
pH, Mix TMR00:09:01 TD00:23:45 CNT: 1234>S 02:34:56 STS:OFF TOT 12:34
Timer Screen, Set Overfeed (S)
pH, Mix TMR00:09:01 TD00:23:45 CNT: 1234 S 02:34:56 STS:OFF >TOT 12:34
Timer Screen, Total Time (TOT)
Enter Enter Enter Enter
pH, Mix TMR00:09:01 >TD00:00:00 CNT: 1234 S 02:34:56 STS:OFF TOT 12:34
Reset Timer, Today (TD)
pH, Mix TMR00:09:01 TD00:23:45 CNT:> 0 S 02:34:56 STS:OFF TOT 12:34
Reset Timer, Count (CNT)
pH, Mix TMR00:09:01 TD00:23:45 CNT: 1234>S 00:00:00 STS:OFF TOT 12:34
Reset Timer, Set Overfeed (S) Reset Timer, Total Time (TOT)
pH, Mix TMR00:09:01 TD00:23:45 CNT: 1234 S 02:34:56 STS:OFF >TOT 0:00
Cycling Through the Timer Screens
There are a total of eight Timer Screens. One Timer Screen is
available for each of the three relays, one for the front panel alarm, and one for each of the four pager/e-mail devices. If relay 3 has not been configured, the Timer Screen for that relay will appear blank. From any Timer Screen, press the [Back] key to return to the Main Status Screen.
The eight Timer Screens are arranged in a specific sequence. Press the up or down arrow keys to cycle from one Timer Screen to another. Each of the Timer Screens corresponds to a number, from [1] to [8]. To jump directly to a specific Timer Screen, press the keypad number associated with that device. For instance, to jump to the Alarm Timer Screen, press the [4] key.
Navigating Within the Timer Screen
Each of the four selectable timers can be manually reset to zero. To reset a specific timer, press the right arrow key to position the cursor next to the timer, then press the [Enter] key. From any Timer Screen, press the [Back] key
to return to the Main Status Screen.
Accessing the Timer Screens
Timer Screens can be accessed from the Main Status Screen. Press the right arrow key to move the cursor to the status indicator of relay 1, 2, or 3 (if configured.) Press the right arrow key again to access the pH Timer
Screen. From there, press the up or down arrow keys to navigate to additional timer screens (see "Cycling Through the Timer Screens" at right).
Use the right arrow key to navigate within the Timer Screen. There four timer cursor positions to cycle through:
Accumulated on-time for the day. Number of relay cycles since last reset. Relay on-time without reaching setpoint. Total on-time since the last reset.
TD:
CNT:
S:
TOT:
Back
AK110 Relay and Alarm Timer Screen Navigation, Rev 3 21 Aug 2008