Pentair AK110 - PROGRAMMING SCREEN NAVIGATION: ORP MIX TIME (1 of 2)

62
pH > 7.67-OFF 7.50s
ORP 490 -OFF 700s _____ 69.0f SW1OFFSW2OFF
Main Status Screen
Name:Main Pool System >Programming
Service Data ( 8:441 ) Communications Security Setup Wizards Serial # 123456
Configuration Menu, Programming
AK110 Programming Screen Navigation, ORP Mix Time (1 of 2)
EnterBack
1:pH, Mix Time >2:ORP, Mix Time 3:Not Used
A:Alarm P:Pager1 P:Pager2 P:Pager3 P:Pager4
Programming Setup Screen ORP Mix, Manual Feed Time
EnterBack
ORP Mix, Proportional Feed Percent ORP Mix, Low ORP Setpoint
ORP Mix, Feed Off if Relay is On
Enter new value Current: 00:02:00 00:02:00 v-Cancel ^
Manual Feed Time Screen Use the keypad to enter the manual sanitizer feed duration. Press the [Enter] key to confirm or the down arrow key to cancel.
Enter
Proportional Feed Percent Screen Use the keypad to enter the proportional feed percentage. Press the [Enter] key to confirm or the down arrow key to cancel.
Enter
Enter new value Current: 5 5 v-Cancel ^ Enter new value Current: 700 700 v-Cancel ^
Use the keypad to enter the ORP setpoint for sanitizer feed control. Press the [Enter] key to confirm or the down arrow key to cancel.
Enter
Low ORP Setpoint Screen
Use the keypad to enter the number of the pH feed control relay to prevent simultaneous chemical feed. Press the [Enter] key to confirm or the down arrow key to cancel. Feed Off if Relay is On Screen
Enter new value Current: 1 1 v-Cancel ^
Use the keypad to enter the time delay between the setpoint trigger and the sanitizer feed cycle start. Press the [Enter] key to confirm or the down arrow key to cancel.
Enter
Delay Time Screen
Enter new value Current: 00:00:20 00:00:20 v-Cancel ^
Enter
Enter
ManualTime 00:02:00<
Proportional% 5 On If ORP< 700 Off If pH> 7.95 Off If pH< 0.00 Off if RLY On 1 On DELAY 00:00:20 On Time 00:01:00 MinTimeOff 00:07:00 Off if Sw1 Off-YES Off if Sw2 On -NO SetOvrfeed 00:00:00 Overfeed 03:00:00
ManualTime 00:02:00 Proportional% 5< On If ORP< 700 Off If pH> 7.95 Off If pH< 0.00 Off if RLY On 1 On DELAY 00:00:20 On Time 00:01:00 MinTimeOff 00:07:00 Off if Sw1 Off-YES Off if Sw2 On -NO SetOvrfeed 00:00:00 Overfeed 03:00:00 ManualTime 00:02:00 Proportional% 5 On If ORP< 700< Off If pH> 7.95 Off If pH< 0.00 Off if RLY On 1 On DELAY 00:00:20 On Time 00:01:00 MinTimeOff 00:07:00 Off if Sw1 Off-YES Off if Sw2 On -NO SetOvrfeed 00:00:00 Overfeed 03:00:00
ORP Mix, Low pH Setpoint
ManualTime 00:02:00 Proportional% 5 On If ORP< 700 Off If pH> 7.95 Off If pH< 0.00< Off if RLY On 1 On DELAY 00:00:20 On Time 00:01:00 MinTimeOff 00:07:00 Off if Sw1 Off-YES Off if Sw2 On -NO SetOvrfeed 00:00:00 Overfeed 03:00:00
ManualTime 00:02:00 Proportional% 5 On If ORP< 700 Off If pH> 7.95 Off If pH< 0.00 Off if RLY On 1< On DELAY 00:00:20 On Time 00:01:00 MinTimeOff 00:07:00 Off if Sw1 Off-YES Off if Sw2 On -NO SetOvrfeed 00:00:00 Overfeed 03:00:00
ORP Mix, Delay Time
ManualTime 00:02:00 Proportional% 5 On If ORP< 700 Off If pH> 7.95 Off If pH< 0.00 Off if RLY On 1 On DELAY 00:00:20< On Time 00:01:00 MinTimeOff 00:07:00 Off if Sw1 Off-YES Off if Sw2 On -NO SetOvrfeed 00:00:00 Overfeed 03:00:00
Enter new value Current: 0.00 0.00 v-Cancel ^
Low pH Setpoint Screen Use the keypad to enter the low pH value under which the sanitizer will not feed. Press the [Enter] key to confirm or the down arrow key to cancel.
To ORP Mix Time (2 of 2)
Note: The relay 2 programming menu appears in this format only when relay 2 has been configured for "ORP Mix Time" control.
Back
Enter
ORP Mix, High pH Setpoint
ManualTime 00:02:00 Proportional% 5 On If ORP< 700 Off If pH> 7.95< Off If pH< 0.00 Off if RLY On 1 On DELAY 00:00:20 On Time 00:01:00 MinTimeOff 00:07:00 Off if Sw1 Off-YES Off if Sw2 On -NO SetOvrfeed 00:00:00 Overfeed 03:00:00
Enter new value Current: 7.95 7.95 v-Cancel ^
Use the keypad to enter the high pH value over which the sanitizer will not feed. Press the [Enter] key to confirm or the down arrow key to cancel. High pH Setpoint Screen
AK110 Programming Screen Navigation, ORP Mix Time, Rev 3 22 Aug 2008
10.8