112
pH > 7.67-OFF 7.50s
ORP 490 -OFF 700s
_____
69.0f SW1OFFSW2OFF
Main Status Screen
Name:Main Pool
System
Programming
Service
>Data ( 30:441 )
Communications
Security Setup
Wizards
Serial # 123456
Configuration Menu, Data
AK110 Data Screen Navigation
Back
EnterBack
07/04 pH ORP Temp
12:00 7.68 745 76.
10:00 7.53 744 76.
08:00 7.45 740 75.
06:00 7.42 740 75.
04:00 7.45 742 76.
02:00 7.59 746 77.
00:00 7.60 750 76.
22:00 7.64 752 75.
Data Display Screen, Current Day
07/03 pH ORP Temp
22:00 7.64 752 75.
20:00 7.52 750 72.
18:00 7.48 746 73.
16:00 7.43 741 74.
14:00 7.55 744 74.
12:00 7.58 749 75.
10:00 7.60 750 75.
08:00 7.61 747 74.
Data Display Screen, Previous Day
Press the up and down arrow keys to
scroll through the recorded data points.
Press the [Back] key to return to the
configuration menu.
Sensor Data as Collected, Recorded and Displayed
07/04 pH ORP Temp
12:00 7.68 745 76.
10:00 7.53 744 76.
08:00 7.45 740 75.
06:00 7.42 740 75.
04:00 7.45 742 76.
02:00 7.59 746 77.
00:00 7.60 750 76.
22:00 7.64 752 75.
07/04 pH ORP Temp
12:00 7.68 745 76.
10:00 7.53 744 76.
08:00 7.45 740 75.
06:00 7.42 740 75.
04:00 7.45 742 76.
02:00 7.59 746 77.
00:00 7.60 750 76.
22:00 7.64 752 75.
07/04 pH ORP Temp
12:00 7.68 745 76.
10:00 7.53 744 76.
08:00 7.45 740 75.
06:00 7.42 740 75.
04:00 7.45 742 76.
02:00 7.59 746 77.
00:00 7.60 750 76.
22:00 7.64 752 75.
Data Display Screen, ORP
07/04 pH ORP Temp
12:00 7.68 745 76.
10:00 7.53 744 76.
08:00 7.45 740 75.
06:00 7.42 740 75.
04:00 7.45 742 76.
02:00 7.59 746 77.
00:00 7.60 750 76.
22:00 7.64 752 75.
Data Display Screen, TemperatureData Display Screen, pHData Display Screen, T imestamp
The second column lists the pH values
as measured by the AK110 and pH
probe.
The third column lists the ORP values
(in millivolts) as measured by the
AK110 and ORP probe.
The fourth column lists the temperature
values (in degrees F or C) as measured
by the AK110 and temperature probe.
The first column lists the date and time
at which each data set was recorded.
Each row comprises a single data set.
The data collected is dependent upon
the type of sensor card installed.
The AK110 data log is capable of storing up to a maximum of 441 data sets in memory at
one time. When this number is exceeded, the oldest data sets are overwritten with the
most recently recorded data.
In its default configuration, the AK110 will record a data set on each of the "even" hours
of a 24-hour clock. This two-hour time interval allows for up to 36 days and 18 hours of
data recordings to be stored in the controller's onboard memory.
Via the System Setup Screen, the controller can be configured to record data sets on an
hourly basis. When so configured, the one-hour time interval allows for up to 18 days
and 9 hours of data recordings to be stored in the controller's onboard memory.
Sensor Data Recording Intervals
07/04 pH ORP Temp
12:00 7.68 745 76.
11:00 7.59 744 76.
10:00 7.53 744 76.
09:00 7.50 743 75.
08:00 7.45 740 75.
07:00 7.44 739 75.
06:00 7.42 740 75.
05:00 7.43 741 76.
07/04 pH ORP Temp
12:00 7.68 745 76.
10:00 7.53 744 76.
08:00 7.45 740 75.
06:00 7.42 740 75.
04:00 7.45 742 76.
02:00 7.59 746 77.
00:00 7.60 750 76.
22:00 7.64 752 75.
Data Display Screen, Hourly IntervalsData Display Screen, 2 Hour Intervals
The last 8 records shown cover a 16
hour time interval.
The last 8 records shown cover an 8-
hour time interval.
If the standard pH/ORP/Temp sensor
card is installed, those specific
measurement types will be recorded in
the data log.
AK110 Data Screen Navigation, Rev 3 21 Aug 2008
10.24
To Next Page
Loading...
