Pentair AK110 - PROGRAMMING SCREEN NAVIGATION: ORP CYCLE TIME (1 of 2)

66
pH > 7.67-OFF 7.50s
ORP 490 -OFF 700s _____ 69.0f SW1OFFSW2OFF
Main Status Screen
Name:Main Pool System >Programming
Service Data ( 8:441 ) Communications Security Setup Wizards Serial # 123456
Configuration Menu, Programming
AK110 Programming Screen Navigation, ORP Cycle Time (1 of 2)
EnterBack
1:pH, Cycle Time >2:ORP, Cycle Time 3:Not Used
A:Alarm P:Pager1 P:Pager2 P:Pager3 P:Pager4
Programming Setup Screen ORP Cycle, Manual Feed Time
EnterBack
ORP Cycle, Proportional Feed Percent ORP Cycle, Low ORP Setpoint ORP Cycle, Feed Off if Relay is On
Enter new value Current: 00:02:00 00:02:00 v-Cancel ^
Manual Feed Time Screen Use the keypad to enter the manual sanitizer feed duration. Press the [Enter] key to confirm or the down arrow key to cancel.
Enter
Proportional Feed Percent Screen Use the keypad to enter the proportional feed percentage. Press the [Enter] key to confirm or the down arrow key to cancel.
Enter
Enter new value Current: 5 5 v-Cancel ^ Enter new value Current: 700 700 v-Cancel ^
Use the keypad to enter the ORP setpoint for sanitizer feed control. Press the [Enter] key to confirm or the down arrow key to cancel.
Enter
Low ORP Setpoint Screen
Use the keypad to enter the number of a pH feed control relay to prevent simultaneous chemical feed. Press the [Enter] key to confirm or the down arrow key to cancel. Feed Off if Relay is On Screen
Enter new value Current: 1 1 v-Cancel ^
Enter Enter
ORP Cycle, Low pH Setpoint
Enter new value Current: 0.00 0.00 v-Cancel ^
Low pH Setpoint Screen Use the keypad to enter the low pH value under which the sanitizer will not feed. Press the [Enter] key to confirm or the down arrow key to cancel.
ManualTime 00:02:00< Proportional% 5 On If ORP< 700 Off If pH> 7.95 Off If pH< 0.00 Off if RLY On 1 Cycle Time 00:02:00 On Limit 00:00:30 Off if Sw1 Off-YES Off if Sw2 On -NO SetOvrfeed 00:00:00 Overfeed 03:00:00
ManualTime 00:02:00 Proportional% 5< On If ORP< 700 Off If pH> 7.95 Off If pH< 0.00 Off if RLY On 1 Cycle Time 00:02:00 On Limit 00:00:30 Off if Sw1 Off-YES Off if Sw2 On -NO SetOvrfeed 00:00:00 Overfeed 03:00:00 ManualTime 00:02:00 Proportional% 5 On If ORP< 700< Off If pH> 7.95 Off If pH< 0.00 Off if RLY On 1 Cycle Time 00:02:00 On Limit 00:00:30 Off if Sw1 Off-YES Off if Sw2 On -NO SetOvrfeed 00:00:00 Overfeed 03:00:00
ManualTime 00:02:00 Proportional% 5 On If ORP< 700 Off If pH> 7.95 Off If pH< 0.00< Off if RLY On 1 Cycle Time 00:02:00 On Limit 00:00:30 Off if Sw1 Off-YES Off if Sw2 On -NO SetOvrfeed 00:00:00 Overfeed 03:00:00 ManualTime 00:02:00 Proportional% 5 On If ORP< 700 Off If pH> 7.95 Off If pH< 0.00 Off if RLY On 1< Cycle Time 00:02:00 On Limit 00:00:30 Off if Sw1 Off-YES Off if Sw2 On -NO SetOvrfeed 00:00:00 Overfeed 03:00:00
To ORP Cycle Time (2 of 2)
Note: The relay 2 programming menu appears in this format only when relay 2 has been configured for "ORP Cycle Time" control.
Enter
Enter new value Current: 7.95 7.95 v-Cancel ^
Use the keypad to enter the high pH value over which the sanitizer will not feed. Press the [Enter] key to confirm or the down arrow key to cancel. High pH Setpoint Screen
ManualTime 00:02:00 Proportional% 5 On If ORP< 700 Off If pH> 7.95< Off If pH< 0.00 Off if RLY On 1 Cycle Time 00:02:00 On Limit 00:00:30 Off if Sw1 Off-YES Off if Sw2 On -NO SetOvrfeed 00:00:00 Overfeed 03:00:00
ORP Cycle, High pH Setpoint
Back
Enter
Enter new value Current: 7.95 7.95 v-Cancel ^
Use the keypad to enter the high pH value over which the sanitizer will not feed. Press the [Enter] key to confirm or the down arrow key to cancel. High pH Setpoint Screen
ManualTime 00:02:00 Proportional% 5 On If ORP< 700 Off If pH> 7.95< Off If pH< 0.00 Off if RLY On 1 Cycle Time 00:02:00 On Limit 00:00:30 Off if Sw1 Off-YES Off if Sw2 On -NO SetOvrfeed 00:00:00 Overfeed 03:00:00
ORP Cycle, High pH Setpoint
AK110 Programming Screen Navigation, ORP Cycle Time, Rev 3 22 Aug 2008
10.9