Pentair AK110 - PROGRAMMING SCREEN NAVIGATION: PAGER 1 (1 of 2)

100
10.20
pH > 7.67-OFF 7.50s
ORP 490 -OFF 700s
_____
69.0f SW1OFFSW2OFF
Main Status Screen
Name:Main Pool
System
>Programming
Service
Data ( 8:441 )
Communications
Security Setup
Wizards
Serial # 123456
Configuration Menu, Programming
AK110 Programming Screen Navigation, Pager 1 (1 of 2)
Enter
Back
1:pH, Mix Time
2:ORP, Mix Time
3:Not Used
A:Alarm
>P:Pager1
P:Pager2
P:Pager3
P:Pager4
Programming Setup Screen
Pager 1, On if Panel Alarm is On
Enter
Back
Pager 1, On if SW1 is Off
Pager 1, Low ORP Setpoint
Pager 1, Not On if Panel Alarm is On
Press the [Enter] key to choose
whether pager 1 is to be used when
the AK110 front panel alarm
indicator is on.
Enter
Pager 1, Not On if SW1 is Off
Enter
Enter new value
Current: 630
630
v-Cancel ^
Use the keypad to enter the low
ORP value under which pager 1 is to
be activated.
Press the [Enter] key to confirm or
the down arrow key to cancel.
Enter
Low ORP Setpoint Screen
Enter
Pager 1, High pH Setpoint
Enter new value
Current: 8.00
8.00
v-Cancel ^
Use the keypad to enter the high pH
value over which pager 1 is to be
activated.
Press the [Enter] key to confirm or
the down arrow key to cancel.
High pH Setpoint Screen
Note:
The Programming Setup Screen
displays four pagers when a dial-up
modem (or no modem at all) is
installed in the controller.
The options available on the Pager
1 Screen programming menu may
vary in accordance with the chosen
configurations for relays 1 and 2.
The programming menus for pagers
2, 3 and 4 are identical to that of
pager 1.
If a cellular modem is installed in
the controller, these four pagers are
replaced with similar E-mail
programming menus.
On If Alarm On YES<
On if Sw1 Off-YES
On If ORP< 630
On If ORP> 770
On If pH> 8.00
On If pH< 7.00
On If Temp< 32.0
On If Temp> 104.0
Off if Sw1 Off-NO
On if Sw2 Off-NO
On If Overfeed YES
On DELAY 00:10:00
On Time 00:00:02
MinTimeOff 12:00:00
On If Alarm On NO <
On if Sw1 Off-YES
On If ORP< 630
On If ORP> 770
On If pH> 8.00
On If pH< 7.00
On If Temp< 32.0
On If Temp> 104.0
Off if Sw1 Off-NO
On if Sw2 On –NO
On if Sw2 Off-NO
On If Overfeed YES
On DELAY 00:10:00
On Time 00:00:02
MinTimeOff 12:00:00
On If Alarm On YES
On if Sw1 Off-YES <
On If ORP< 630
On If ORP> 770
On If pH> 8.00
On If pH< 7.00
On If Temp< 32.0
On If Temp> 104.0
Off if Sw1 Off-NO
On if Sw2 Off-NO
On If Overfeed YES
On DELAY 00:10:00
On Time 00:00:02
MinTimeOff 12:00:00
On If Alarm On YES
On if Sw1 Off-NO <
On If ORP< 630
On If ORP> 770
On If pH> 8.00
On If pH< 7.00
On If Temp< 32.0
On If Temp> 104.0
Off if Sw1 Off-NO
On if Sw2 Off-NO
On If Overfeed YES
On DELAY 00:10:00
On Time 00:00:02
MinTimeOff 12:00:00
On If Alarm On YES
On if Sw1 Off-YES
On If ORP< 630<
On If ORP> 770
On If pH> 8.00
On If pH< 7.00
On If Temp< 32.0
On If Temp> 104.0
Off if Sw1 Off-NO
On if Sw2 Off-NO
On If Overfeed YES
On DELAY 00:10:00
On Time 00:00:02
MinTimeOff 12:00:00
Press the [Enter] key to choose
whether pager 1 is to be used when
the flow switch SW1 is off.
On If Alarm On YES
On if Sw1 Off-YES
On If ORP< 630
On If ORP> 770
On If pH> 8.00<
On If pH< 7.00
On If Temp< 32.0
On If Temp> 104.0
Off if Sw1 Off-NO
On if Sw2 Off-NO
On If Overfeed YES
On DELAY 00:10:00
On Time 00:00:02
MinTimeOff 12:00:00
Enter
Pager 1, Low pH Setpoint
Enter new value
Current: 7.00
7.00
v-Cancel ^
Use the keypad to enter the low pH
value under which pager 1 is to be
activated.
Press the [Enter] key to confirm or
the down arrow key to cancel.
Low pH Setpoint Screen
On If Alarm On YES
On if Sw1 Off-YES
On If ORP< 630
On If ORP> 770
On If pH> 8.00
On If pH< 7.00<
On If Temp< 32.0
On If Temp> 104.0
Off if Sw1 Off-NO
On if Sw2 Off-NO
On If Overfeed YES
On DELAY 00:10:00
On Time 00:00:02
MinTimeOff 12:00:00
Enter
Pager 1, Low Temperature Setpoint
Enter new value
Current: 32.0
32.0
v-Cancel ^
Use the keypad to enter the low
temperature value under which
pager 1 is to be activated.
Press the [Enter] key to confirm or
the down arrow key to cancel.
Low Temperature Setpoint Screen
On If Alarm On YES
On if Sw1 Off-YES
On If ORP< 630
On If ORP> 770
On If pH> 8.00
On If pH< 7.00
On If Temp< 32.0<
On If Temp> 104.0
Off if Sw1 Off-NO
On if Sw2 Off-NO
On If Overfeed YES
On DELAY 00:10:00
On Time 00:00:02
MinTimeOff 12:00:00
To Pager 1 (2 of 2)
Back
Pager 1, High ORP Setpoint
Enter
High ORP Setpoint Screen
Enter new value
Current: 770
770
v-Cancel ^
Use the keypad to enter the high
ORP value over which pager 1 is to
be activated.
Press the [Enter] key to confirm or
the down arrow key to cancel.
On If Alarm On YES
On if Sw1 Off-YES
On If ORP< 630
On If ORP> 770<
On If pH> 8.00
On If pH< 7.00
On If Temp< 32.0
On If Temp> 104.0
Off if Sw1 Off-NO
On if Sw2 Off-NO
On If Overfeed YES
On DELAY 00:10:00
On Time 00:00:02
MinTimeOff 12:00:00
AK110 Programming Screen Navigation, Pager 1, Rev 3 22 Aug 2008