Pentair AK110 - PROGRAMMING SCREEN NAVIGATION: DAILY EVENT (2 of 2)

93
pH > 7.67-OFF 7.50s
ORP 490 -OFF 700 Daily -OFF 69.0f SW1OFFSW2OFF
Main Status Screen
Name:Main Pool System >Programming
Service Data ( 8:441 ) Communications Security Setup Wizards Serial # 123456
Configuration Menu, Programming
AK110 Programming Screen Navigation, Daily Event
EnterBack
1:pH, Mix Time 2:ORP, Mix Time >3:Daily
A:Alarm P:Pager1 P:Pager2 P:Pager3 P:Pager4
Programming Setup Screen Daily Event, Manual Cycle Time
EnterBack
Enter new value Current: 00:02:00 00:02:00 v-Cancel ^
Manual Cycle Time Screen Use the keypad to enter the manual relay on-time duration. Press the [Enter] key to confirm or the down arrow key to cancel.
Enter
Enter
Enter
Press the [Enter] key to make the relay operation dependent or independent of the status of switch 2 (SW2.)
Note: The relay 3 programming menu appears in this format only when relay 3 has been configured for "Daily" control.
Daily Event, Off if Time is After
Enter
Daily Event, Minimum Time Off Daily Event, Relay On if SW2 is On
Enter new value Current: 00:02:00 00:02:00 v-Cancel ^
Use the keypad to enter the maximum relay on-time duration. Press the [Enter] key to confirm or the down arrow key to cancel. Use the keypad to enter the time after which the relay will turn off. Press the [Enter] key to confirm or the down arrow key to cancel. On Calculated Time Screen Off if Time is After Screen
Daily Event, Off if Time is Before Off if Time is Before Screen
Enter
Daily Event, On Calculated Time
Enter
Enter new value Current: 00:05:00 00:05:00 v-Cancel ^
Minimum Time Off Screen Daily Event, Independent of SW2 Use the keypad to enter the amount of time the relay will be held off before it is allowed to turn on again. Press the [Enter] key to confirm or the down arrow key to cancel.
ManualTime 00:02:00<
** ON ** OffIfTime> 01:01:02 OffIfTime< 01:01:00 OnCTime 00:02:00 MinTimeOff 00:05:00 On if Sw2 On -YES Off if Sw1 Off-YES
ManualTime 00:02:00 ** ON ** OffIfTime> 01:01:02<
OffIfTime< 01:01:00 OnCTime 00:02:00 MinTimeOff 00:05:00 On if Sw2 On -YES Off if Sw1 Off-YES
ManualTime 00:02:00 ** ON ** OffIfTime> 01:01:02 OffIfTime< 01:01:00<
OnCTime 00:02:00 MinTimeOff 00:05:00 On if Sw2 On -YES Off if Sw1 Off-YES
ManualTime 00:02:00 ** ON ** OffIfTime> 01:01:02 OffIfTime< 01:01:00 OnCTime 00:02:00< MinTimeOff 00:05:00 On if Sw2 On -YES Off if Sw1 Off-YES
ManualTime 00:02:00 ** ON ** OffIfTime> 01:01:02 OffIfTime< 01:01:00 OnCTime 00:02:00 MinTimeOff 00:05:00< On if Sw2 On -YES Off if Sw1 Off-YES ManualTime 00:02:00 ** ON ** OffIfTime> 01:01:02 OffIfTime< 01:01:00 OnCTime 00:02:00 MinTimeOff 00:05:00 On if Sw2 On –YES < Off if Sw1 Off-YES
ManualTime 00:02:00 ** ON ** OffIfTime> 01:01:02 OffIfTime< 01:01:00 OnCTime 00:02:00 MinTimeOff 00:05:00 On if Sw2 On –NO < Off if Sw1 Off-YES
Enter new value Current: 01:01:00 01:01:00 v-Cancel ^ Enter new value Current: 01:01:02 01:01:02 v-Cancel ^
Use the keypad to enter the time before which the relay will turn off. Press the [Enter] key to confirm or the down arrow key to cancel.
Back
Enter
Press the [Enter] key to make the relay operation dependent or independent of the status of the flow switch SW1.
Daily Event, Relay Off if SW1 is Off Daily Event, Independent of SW1
ManualTime 00:02:00 ** ON ** OffIfTime> 01:01:02 OffIfTime< 01:01:00 OnCTime 00:02:00 MinTimeOff 00:05:00 On if Sw2 On -YES Off if Sw1 Off-YES <
ManualTime 00:02:00 ** ON ** OffIfTime> 01:01:02 OffIfTime< 01:01:00 OnCTime 00:02:00 MinTimeOff 00:05:00 On if Sw2 On -YES Off if Sw1 Off-NO <
AK110 Programming Screen Navigation, Daily Event, Rev 3 22 Aug 2008