Index-1
A
AC power
how to connect to 5-2
specifications 11-8
AC power cord, how to install A-7–A-8
Accessories, part numbers C-1–C-4
Air inlet filter. See Filter, air inlet
Alarm LED
description 3-7
state during alarm conditions 9-3
Alarm Reset button, function 9-5
Alarm Silence button, function 9-5
Alarm tests 5-9–5-10
Alarm Volume Escalation
definition E-11
how to enable or disable E-11
status display 6-17
Alarms
adjustable, specifications 11-4
Check Vent (high-priority), description 9-3
Check Vent, troubleshooting table 9-12–9-16
high-priority, description 9-3
how to clear autoreset alarms from the Alarms list 9-5
how to hide/display messages 9-6
how to manually reset 9-5
how to respond to 9-1
how to set 6-12
how to silence 9-5
loudness, how to adjust 6-17
low-priority, description 9-3
messages, list 9-7–9-17
See also name of specific alarm
settings
how to change 6-12
list of descriptions and ranges 6-26–6-27
troubleshooting table 9-7–9-17
Vent Inoperative (high-priority), description 9-3
Vent Inoperative, troubleshooting table 9-16–9-17
visual alarm indications 9-2
Alarms and messages 9-1–9-17
Assembly, ventilator A-2–A-8
Auto-Trak sensitivity
description 3-3
principles of operation 4-3–4-6
Auto-Trak+ option
description 4-6
how to change settings 6-18–6-19
settings and ranges 11-4
AVAPS (average volume-assured pressure support) mode
precautions 1-1, 1-2
principles of operation 4-11–4-12
AVAPS Maximum IPAP Pressure setting. See Max P
AVAPS Minimum IPAP Pressure setting. See Min P
AVAPS: Target V
T
Exceeded. Min Pressure Too High mes-
sage 9-7
AVAPS: Target V
T
Not Achieved. Insufficient Max Pressure
message 9-7
Average volume-assured pressure support mode. See AVAPS
mode
B
Backup alarm 3-10
Backup battery. See Battery, backup
Bacteria filter must be installed onto gas outlet message 9-7
Baseline pressure, description 4-2
Batch settings, how to make 6-3, 6-19
Battery, backup
description 3-10–3-11
how to install A-4–A-6
location 3-9
operation time 3-10
part number C-4
specifications 11-8
Baud rate
for ventilator used with Philips monitor and VueLink
Open Interface B-2
how to change E-10
Breath frequency. See Rate
Breath phase/trigger indicator, definition 8-2
Breathing circuit. See Patient circuit
Brightness, display, how to set 6-17
Buzzer, backup 3-10
C
Calibration, touchscreen E-14
Cannot Reach Target Flow alarm 7-7, 9-7
Care and maintenance 10-1–10-9
C-Flex setting, definition 6-23
Check Vent alarm, description 9-3
Check Vent: 1.8 V Supply Failed alarm 9-12
Check Vent: 12 V Supply Failed alarm 9-12
Check Vent: 24 V Supply Failed alarm 9-12
Check Vent: 3.3 V Supply Failed alarm 9-12
Check Vent: 35 V Supply Failed alarm 9-13
Check Vent: 5 V Supply Failed alarm 9-12
Check Vent: Air Flow Sensor Calibration Data Error alarm 9-
13
Check Vent: Alarm LED Failed alarm 9-13
Check Vent: Auxiliary Alarm Supply Failed alarm 9-13
Check Vent: Backup Alarm Failed alarm 9-13
Check Vent: Barometer Calibration Data Error alarm 9-13
Check Vent: Barometer Sensor Range Error alarm 9-13
Check Vent: Battery Failed alarm 9-13
Check Vent: Battery Temperature High alarm 9-13
Check Vent: Blower Stalled 9-14
Check Vent: Blower Temperature High alarm 9-14
Check Vent: Cooling Fan Speed Error alarm 9-14
Check Vent: CPU PCBA ADC Failed alarm 9-14
Check Vent: Data Acquisition PCBA ADC Failed alarm 9-14
Check Vent: Flash File System Error alarm 9-14
Check Vent: Internal Temperature High CPU alarm 9-14
Check Vent: Internal Temperature High Daq alarm 9-14
Index
To Next Page
Loading...
