Rapid Shape D50+

To Next Page

To Previous Page

Operating Instructions D50+ | P50+ | SHERAprint 50

Rapid Shape GmbH │ DOCR000438

92 │ 96

8. Dispose of the used blade as intended according to local waste

disposal regulations.

Main Page

Table of Contents3
Safety7
Symbols in this Manual7
Intended Use9
Digital Workflow9
Safety Devices10
Protective Hoods10
Hood Switch10
Knife Protection Device11
Attached Safety Markings12
Residual Risks13
Electrical Current13
Mechanical Dangers14
UV Radiation14
Chemical Dangers15
Danger Due to Hot Surfaces15
Danger of Material Damage15
Personnel Requirements17
Personal Protective Equipment18
Environmental Protection18
Overview19
Machine Assembly & Operating Elements19
Serial Plate22
Transport & Storage23
Transporting the Machine23
Unpacking the Machine24
Scope of Delivery25
Storing the Machine25
Installation26
Setting up26
Requirements for the Installation Location26
Setting up the Machine26
Aligning the Machine27
Connecting the Machine29
Setting up the Wi-Fi Connection30
Connecting the Machine to Other Devices (Intelligent Connectivity)30
Emergency Shutdown31
Preparations32
Required Accessories32
Print Accessories32
IT Requirements32
Netfabb33
Operation34
Switching on the Machine34
Switching on the Machine for the First Time34
Switching on the Machine in Daytime Mode35
Menu Overview36
Verifying the Machine Status36
Opening & Closing the Machine37
Opening & Closing the Machine with the Foot Sensor37
Opening & Closing the Machine Manually37
Automatic Hood Closing38
Making General Settings in the Customer Menu39
Hide Warnings (Reservoir Inserted)39
Disable Automatic Updates39
Enable Automatic Part Separation40
Show Detailed Printing Screen40
Intelligent Connectivity40
Disable Mixing41
Disable Automatic Hood41
Disable Hood Assistant41
Enable Automatic Refill41
Move Jobs in Queue on Complete42
Maximum Jobs in Basket42
Offset Part Detection42
Preparing the Machine for Printing (Start of the Day)43
Checking the Individual Components for Cleanliness43
Inserting the Build Platform44
Inserting the Knife Drip Guard & the Knife45
Inserting the Material Reservoir47
Inserting the Collection Basket48
Connecting the Hose (Automatic Refill)48
Setting up & Administrating the Automatic Separation Function49
Operation with Automatic Separation Function49
Operation Without Automatic Separation Function50
Printing Jobs51
Starting the Print Job51
Switching the Print View52
Pausing Jobs & Ending Them Prematurely53
Side Note: Integrated Heating Function54
Refilling Printing Material56
Refilling Printing Material Manually56
Automatic Refill: Refilling the Printing Material Automatically57
Automatic Refill: Replacing the Material Bottle (Empty > Full)59
Automatic Refill: Re-Pumping Printing Material Manually60
Removing Jobs61
Removing Jobs with the Automatic Separation Function61
Removing Jobs Without Automatic Separation Function (Manually)62
Post-Processing Jobs63
Cleaning Jobs63
Post-Curing Jobs64
Checking Your Jobs64
Changing Printing Material65
Machine Follow-Up (End of Day)66
Decommissioning67
Switching off the Machine67
Switching off the Machine in Daytime Mode67
Switching off the Machine for a Prolonged Period of Time (> 1 Week)67
Shutting down the Machine for a Long Period of Time (> 1 Month)67
Troubleshooting68
Cleaning & Maintenance69
Overview of the Cleaning & Maintenance Work69
Cleaning the Protective Glass70
Cleaning the Build Platform71
Cleaning the Knife73
Cleaning the Knife Drip Guard75
Cleaning the Material Reservoir76
Cleaning the Collection Basket78
Calibrating the Exposure Unit (One-Point Calibration)79
Checking the Separation Unit81
Checking the Refill Unit82
10.1.10 Checking & Adjusting the Parallelism of the Build Platform83
Performing Automatic Reservoir Cleaning (Clean Reservoir)86
10.1.12 Cleaning the Hose88
10.1.13 Changing the Knife91
10.1.14 Changing the Hose93
Disassembly & Disposal94
Disassemble the Machine94
Dispose of the Machine95
Technical Details96

Rapid Shape D50+ - Page 92

Table of Contents

Related product manuals