Roland AE-30 - Tone;Structure

36
Tone Parameters
Structure lets you sound two partials as a set.
You can create a wide range of sounds by using partial 2 or 4 (the modulator)
to modulate partial 1 or 3 (the carrier).
Since the Structure uses two partials as a pair, it provides parameters that
are used in common by the carrier and modulator.
For the following parameters, only the partial settings of the carrier are
valid (the settings of the modulator are ignored).
TONE/PARTIAL/RANGE
5 Key Range Lower
5 Key Range Upper
5 Key Fade Lower
5 Key Fade Upper
5 Velocity Range Lower
5 Velocity Range Upper
5 Velocity Fade Low
5 Velocity Fade Up
TONE/PARTIAL
5 Partial Switch
TONE/PARTIAL/OSC
5 Delay Mode
5 Delay Time Sync
5 Delay Time (note)
5 Delay Time
TONE/PARTIAL/CONTROL
5 Envelope Mode
5 Receive Hold-1
5 Redamper Switch
5 Damper Free Note
TONE/PARTIAL/MATRIX CONTROL
5 Destination: PMT
5 Destination: CROSS-MOD
Parameter Value Explanation
Structure1-2
The sound of partial 1 is modulated by partial 2.
OFF O
SYNC
Implements the oscillator sync function
that is provided by an analog synthesizer.
The partial 1 oscillator is reset at intervals
of partial 2’s pitch cycle.
* This is valid when the OSC Type
(p. 39) is “VA” or “PCM-Sync.”
RING
Implements the ring modulator function
that is provided by an analog synthesizer.
The output sound of partial 2 is multiplied
with partial 1.
XMOD, XMOD2
Implements the cross modulation
function that is provided by an analog
synthesizer.
The output sound of partial 2 is applied
as the pitch of partial 1.
XMOD2 is available only when Partial 1
and 3 are OSC Type (p. 39) “VA.”
Structure3-4
The sound of partial 3 is modulated by partial 4.
OFF O
SYNC
Implements the oscillator sync function
that is provided by an analog synthesizer.
The partial 3 oscillator is reset at intervals
of partial 4’s pitch cycle.
* This is valid when the OSC Type
(p. 39) is “VA” or “PCM-Sync.”
RING
Implements the ring modulator function
that is provided by an analog synthesizer.
The output sound of partial 4 is
multiplied with partial 3.
XMOD, XMOD2
Implements the cross modulation
function that is provided by an analog
synthesizer.
The output sound of partial 4 is applied
as the pitch of partial 3.
XMOD2 is available only when Partial 1
and 3 are OSC Type (p. 39) “VA.”
Partial Phase Lock OFF, ON
It locks the waveform phase between
partials.
It is eective to use this with XMOD2.
* This is valid when the OSC Type
(p. 39) is “VA.”
RING
1-2 Level 0–127 RING level when Structure1-2 is “RING.”
3-4 Level 0–127 RING level when Structure3-4 is “RING.”
OSC1 Level 0–127
Sets the partial 1 OSC level.
* This is valid when the Structure1-2 is
“RING.”
OSC2 Level 0–127
Sets the partial 2 OSC level.
* This is valid when the Structure1-2 is
“RING.”
OSC3 Level 0–127
Sets the partial 3 OSC level.
* This is valid when the Structure3-4 is
“RING.”
OSC4 Level 0–127
Sets the partial 4 OSC level.
* This is valid when the Structure3-4 is
“RING.”
TONE/STRUCTURE