Roland AE-30 - Guitar Amp Sim (Guitar Amp Simulator)

57
MFX/IFX Parameters
32 Guitar Amp Sim
(Guitar Amp Simulator)
This is an effect that simulates the sound of a guitar amplifier.
L in
R in
SpeakerPre Amp
L out
R out
Pan L
Pan R
Parameter Value Explanation
Pre Amp Switch OFF, ON Turns the amp switch on/off.
Pre Amp Type
Type of guitar amp
JC-120
This models the sound of the Roland
JC-120.
CLEAN TWIN This models a Fender Twin Reverb.
MATCH DRIVE
This models the sound input to left input
on a Matchless D/C-30.
A simulation of the latest tube amp widely
used in styles from blues and rock.
BG LEAD
This models the lead sound of the MESA/
Boogie combo amp.
The sound of a tube amp typical of the late
‘70s to ‘80s.
MS1959I
This models the sound input to Input I on
a Marshall 1959.
This is a trebly sound suited to hard rock.
MS1959II
This models the sound input to Input II on
a Marshall 1959.
MS1959I+II
This models the sound of connecting
inputs I and II on a Marshall 1959 in
parallel. It creates a sound with a stronger
low end than I.
SLDN LEAD
This models a Soldano SLO-100. This is the
typical sound of the eighties.
METAL 5150
This models the lead channel of a Peavey
EVH5150.
METAL LEAD
This is distortion sound that is ideal for
performances of heavy riffs.
OD-1
This models the sound of the BOSS OD-1.
This produces sweet, mild distortion.
OD-2 TURBO
This is the high-gain overdrive sound of
the BOSS OD-2.
DISTORTION
This gives a basic, traditional distortion
sound.
FUZZ A fuzz sound with rich harmonic content.
Pre Amp Volume 0–127
Volume and amount of distortion of the
amp
Pre Amp Master 0–127 Volume of the entire pre-amp
Pre Amp Gain
LOW, MIDDLE,
HIGH
Amount of pre-amp distortion
Pre Amp Bass
0–127
Tone of the bass/mid/treble frequency
range
Pre Amp Middle
Pre Amp Treble
Pre Amp Presence 0–127 Tone for the ultra-high frequency range
Pre Amp Bright OFF, ON
Turning this “On” produces a sharper and
brighter sound.
* This parameter applies to the “JC-120,”
“CLEAN TWIN,” “MATCH DRIVE,” and “BG
LEAD” Pre Amp Types.
Speaker Switch OFF, ON
Determines whether the signal passes
through the speaker (ON), or not (OFF).
Parameter Value Explanation
Speaker Type
Cabinet
Diameter (in
inches) and
number of the
speaker
Microphone
SMALL 1
Small open-
back enclosure
10 Dynamic
SMALL 2
Small open-
back enclosure
10 Dynamic
MIDDLE
Open back
enclosure
12 x 1 Dynamic
JC-120
Open back
enclosure
12 x 2 Dynamic
BUILT-IN 1
Open back
enclosure
12 x 2 Dynamic
BUILT-IN 2
Open back
enclosure
12 x 2 Condenser
BUILT-IN 3
Open back
enclosure
12 x 2 Condenser
BUILT-IN 4
Open back
enclosure
12 x 2 Condenser
BUILT-IN 5
Open back
enclosure
12 x 2 Condenser
BG STACK1
Sealed
enclosure
12 x 2 Condenser
BG STACK2
Large sealed
enclosure
12 x 2 Condenser
MS STACK1
Large sealed
enclosure
12 x 4 Condenser
MS STACK2
Large sealed
enclosure
12 x 4 Condenser
METAL STACK
Large double
stack
12 x 4 Condenser
2-STACK
Large double
stack
12 x 4 Condenser
3-STACK
Large triple
stack
12 x 4 Condenser
Mic Setting 1, 2, 3
Adjusts the location of the microphone
that is recording the sound of the speaker.
This can be adjusted in three steps, with
the microphone becoming more distant in
the order of 1, 2, and 3.
Mic Level 0–127 Volume of the microphone
Direct Level 0–127 Volume of the direct sound
Pan L64–63R Stereo location of the output sound
Level 0–127 Output Level