63
MFX/IFX Parameters
75 2Tap Pan Dly
(2 Tap Pan Delay)
R out
L out
Balance W
Balance W
Balance D
Balance D
L in
Double Tap
Delay
Double Tap
Delay
R in
Delay 1
Feedback
Delay 2
Parameter Value Explanation
Delay Time
(sync sw)
OFF, ON
If this is ON, the delay synchronizes with
the tempo.
Delay Time (msec) 1–2600 (msec)
Adjusts the delay time from the direct
sound until the second delay sound is
heard.
Delay Time (note)
Note
& “Note” (p. 64)
Feedback -98–+98 (%)
Adjusts the proportion of the delay sound
that is fed back into the effect. Negative
(-) settings will invert the phase.
HF Damp
200, 250, 315, 400,
500, 630, 800, 1000,
1250, 1600, 2000,
2500, 3150, 4000,
5000, 6300, 8000,
BYPASS (Hz)
Adjusts the frequency above which the
delay sound fed back to the effect is
filtered out (BYPASS: no cut).
Delay 1 Pan L64–63R Stereo location of Delay 1
Delay 2 Pan L64–63R Stereo location of Delay 2
Delay 1 Level 0–127 Volume of delay 1
Delay 2 Level 0–127 Volume of delay 2
Low Gain -15–+15 (dB) Gain of the low range
High Gain -15–+15 (dB) Gain of the high range
Balance D100:0W–D0:100W
Adjusts the volume balance between the
sound that is sent through the delay (W)
and the sound that is not sent through
the delay (D).
Level 0–127 Output Level
86 Fuzz
Adds overtones and intensely distorts the sound.
L in L out
R outR in
Parameter Value Explanation
Drive 0–127
Adjusts the amount of distortion.
This also changes the volume.
Tone 0–100 Sound quality of the Overdrive effect
Level 0–127 Output Level
87 JUNO-106 Chorus
This models the chorus effects of the Roland JUNO-106.
L out
R out
L in
R in
Noise
Generator
Noise
Generator
Parameter Value Explanation
Mode I, II, I+II, JX I, JX II
Type of Chorus
I+II: The state in which two buttons are
pressed simultaneously.
Noise Level 0–127 Volume of the noise produced by chorus
Balance D100:0W–D0:100W
Volume balance between the dry sound
(D) and effect sound (W)
Level 0–127 Output Level
92 Exciter
This adds dynamics to the sound, by dynamically bringing up the
high end using a split-band compressor.
* This effect can be used as an IFX. The effect is not available for the
MFX.
L out
Low
Mid
High
L in
Compressor
Compressor
Channel
Divider
R out
Low
Mid
High
R in
Compressor
Compressor
Channel
Divider
Parameter Value Explanation
Band2 Threshold -80.0–0.0 (dB)
Raises the midrange frequency levels
when they fall below the specified
amount.
Band2 Max Gain 0–+24 (dB)
Sets how much to raise the levels when
the midrange volume is low.
Band3 Threshold -80.0–0.0 (dB)
Raises the high-end frequency levels
when they fall below the specified
amount.
Band3 Max Gain 0–+24 (dB)
Sets how much to raise the levels when
the high-end frequency volume is low.
Split1 Frequency 2000–5000 (Hz)
Frequency at which the low and
midrange frequencies are split
Split2 Frequency 3000–10000 (Hz)
Frequency at which the midrange and
high-end frequencies are split
Level 0–127 Output Level
To Next Page
Loading...
