Roland AE-30 - Scene;Reverb; Reverb Parameters

31
Scene Parameters
SCENE/REVERB
Parameter Value Explanation
RV SW
OFF, ON Switches the reverb on/o.
Reverb Type
Selects the types of reverb.
OFF, 1 INTEGRA7Rev, 2 Warm Hall, 3 Hall, 4 GS Reverb, 5 SRV-2000, 6 SRV-2000NL, 7 GM2 Reverb
FX
Reverb parameters
Congure the parameters of the selected reverb type.
See “Reverb parameters”
The available parameters dier depending on the type of reverb you selected in
Reverb Type.
OUTPUT
Reverb Level
0–127
Sets the amount of reverb.
If you don’t want to add the reverb eect, set it to 0.
Reverb Parameters
1 INTEGRA7Rev (INTEGRA 7 Reverb)
Parameter Value Explanation
Char
ROOM1–2,
HALL1–2,
PLATE
Type of reverb
PreDelay 0–100
Adjusts the delay time from the
direct sound until the reverb
sound is heard.
Time 0.1–10.0 (sec)
Adjusts the decay length of the
reverb sound.
Density 0–127
Adjusts the density of the reverb
sound.
Diusion 0–127
Adjusts the change in the density
of the reverb over time.
The higher the value, the more
the density increases with time.
(The eect of this setting is most
pronounced with long reverb
times.)
LF Damp 0–100
Adjusts the low-frequency
portion of the reverb.
HF Damp 0–100
Adjusts the high-frequency
portion of the reverb.
Spread 0–127 Reverb spread
Tone 0–127 Tonal character of the reverb
2 Warm Hall
Parameter Value Explanation
PreDelay 0–100
Adjusts the delay time from the
direct sound until the reverb
sound is heard.
Time 0.3–30.0 (sec)
Adjusts the decay length of the
reverb sound.
Pre LPF (*3)
Frequency above which to cut
the high-frequency portion of
the sound entering the reverb
Pre HPF (*4)
Frequency below which to cut
the low-frequency portion of the
sound entering the reverb
PreLoop LPF (*3)
Frequency above which to cut
the high-frequency portion of
the extended reverberation
Diusion 0–127
Adjusts the change in the density
of the reverb over time.
HF Damp Freq (*5)
Adjusts the frequency above
which to cut the high-frequency
portion of the reverb.
HF Damp Ratio 0.1–1.0
Adjusts the amount by which to
attenuate the high-frequency
portion of the reverb.
(*3) 16, 20, 25, 32, 40, 50, 63, 80, 100, 125, 160, 200, 250, 315, 400, 500,
630, 800, 1000, 1250, 1600, 2000, 2500, 3150, 4000, 5000, 6300,
8000, 10000, 12500, 15000 (Hz), BYPASS
(*4) BYPASS, 16, 20, 25, 32, 40, 50, 63, 80, 100, 125, 160, 200, 250, 315,
400, 500, 630, 800, 1000, 1250, 1600, 2000, 2500, 3150, 4000,
5000, 6300, 8000, 10000, 12500, 15000 (Hz)
(*5) 1000, 1250, 1600, 2000, 2500, 3150, 4000, 5000, 6300, 8000 (Hz)