Roland AE-30 - Scene;Control (MIDI); Scene;Part; Scene;Mode

24
Scene Parameters
SCENE/CONTROL (MIDI)
* The following settings are enabled when MIDI control mode is on.
Parameter Value Explanation
Tx Channel
1–16 Species the MIDI transmit chaunnel.
Bank MSB (CC#0)
OFF, 0–127 Sets the bank select/program change message that is transmitted when a scene is
selected.
When this is set to “OFF,” no bank select/program change is transmitted.
* These parameters are enabled when the MIDI Ctrl PC and MIDI Ctrl BS (p. 7)
system parameters are set to “On.”
Bank LSB (CC#32)
OFF, 0–127
PC
OFF, 1–128
Velocity
These parameters set the note-on velocity values for MIDI output.
REAL The velocity value is determined by the strength of your tonguing.
1–127 Transmits the specied value (a xed value).
Volume (CC#7)
OFF, 0–127
Sets the value transmitted for Volume (CC#7) when a scene is selected.
When this is set to “OFF,” no bank select/program change is transmitted.
Pan (CC#10)
OFF, L64–0–63R
Sets the value transmitted for PAN (#CC#10) when a scene is selected.
When this is set to “OFF,” no bank select/program change is transmitted.
Modulation (CC#1)
OFF, 0–127
Sets the value transmitted for Modulation (CC#1) when a scene is selected.
When this is set to “OFF,” no bank select/program change is transmitted.
Reverb (CC#91)
Sets the value transmitted for Reverb Send (CC#91) when a scene is selected.
When this is set to “OFF,” no bank select/program change is transmitted.
Chorus (CC#93)
Sets the value transmitted for Chorus Send (CC#93) when a scene is selected.
When this is set to “OFF,” no bank select/program change is transmitted.
Coarse (RPN#2)
OFF, -48–0–+48
Sets the value transmitted for Coarse Tune (RPN#2) when a scene is selected.
When this is set to “OFF,” no bank select/program change is transmitted.
Fine Tune (RPN#1)
OFF, -50–0–+50
Sets the value transmitted for Fine Tune (RPN#1) when a scene is selected.
When this is set to “OFF,” no bank select/program change is transmitted.
Bend Rng (RPN#0)
OFF, 0–24
Sets the value transmitted for Bend Range (RPN#0) when a scene is selected.
When this is set to “OFF,” no bank select/program change is transmitted.
Cuto (CC#74)
OFF, 0–127
Sets the value transmitted for Cuto Oset (CC#74) when a scene is selected.
When this is set to “OFF,” no bank select/program change is transmitted.
Resonance (CC#71)
Sets the value transmitted for Resonance Oset (CC#71) when a scene is selected.
When this is set to “OFF,” no bank select/program change is transmitted.
Attack (CC#73)
Sets the value transmitted for Attack Time Oset (CC#73) when a scene is selected.
When this is set to “OFF,” no bank select/program change is transmitted.
Decay (CC#75)
Sets the value transmitted for Decay Time Oset (CC#75) when a scene is selected.
When this is set to “OFF,” no bank select/program change is transmitted.
Release (CC#72)
Sets the value transmitted for Release Time Oset (CC#72) when a scene is selected.
When this is set to “OFF,” no bank select/program change is transmitted.
MONO/POLY
(CC#126/127)
OFF, MONO (CC#126),
POLY (CC#127)
Sets the value transmitted for Mono/Poly (CC#126/127) when a scene is selected.
When this is set to “OFF,” no bank select/program change is transmitted.
SCENE/PART
Parameter Value Explanation
PartSW OFF, ON Turns each part (PART 1–4) on/o.
SCENE/MODE
Parameter Value Explanation
Part Mode
Species the part mode.
LEAD This is the usual mode for playing melodies and the like.
DRONE
This is a special mode for playing sustaining low notes.
This mode is used with the assign function set to “Drone Sw” (p. 12).