UPPER > LOWER:
Copy the Upper patch to the Lower.
LOWER > UPPER:
Copy the Lower patch to the Upper.
SWAP U <-> L:
Exchange the Upper patch and Lower patch.
4 Press [WRITE].
The display will indicate “Completed,” and then the
previous display will reappear.
The patch has now been copied or exchanged.
* For details on copying patterns, refer to page 97.
Selecting Patches from an
External Device
Patches can be selected by transmitting Bank Select (con-
troller number 0, 32) and Program Change messages from a
connected MIDI keyboard etc. to the JP-8080.
In this case, the settings will differ slightly depending on
whether the external MIDI device is connected to the
REMOTE KBD IN connector or to the MIDI IN connector.
Connection to the REMOTE KBD IN connector
1 Use a MIDI cable to connect the MIDI OUT connec-
tor of the external MIDI device to the JP-8080’s
REMOTE KBD IN connector.
2 Press [PERFORM/PATCH SELECT] so that the
upper left of the display reads “PATCH.”
3 Set the JP-8080’s Remote Keyboard Channel
(Remote KBD CH) either to ALL or to the same
number as the transmit channel of your external
MIDI device.
1) Press [EDIT]. (The indicator will light.)
2) Press [MIDI] (BANK [5]) several times to select
“Remote KBD CH.”
3) Press [DEC]/[INC] to set the channel.
* After making the setting, be sure to press [EDIT] or
[EXIT] so that the upper left of the display reads
“PATCH.”
4 Use the PANEL SELECT [LOWER]/[UPPER] but-
tons to select the part whose patch you wish to
change.
You can press both [LOWER] and [UPPER] simultane-
ously to make both indicators light, and select the same
Patch for both Parts at the same time.
5 Transmit a Bank Select MSB (controller number 0)
message to the JP-8080.
6 Transmit a Bank Select LSB (controller number 32)
message to the JP-8080.
7 Transmit a Program Change message to the JP-8080.
Connection to the MIDI IN connector
1 Use a MIDI cable to connect the MIDI OUT connec-
tor of the external MIDI device to the JP-8080’s
MIDI IN connector.
2 Set the MIDI channel of each JP-8080 Part to match
the transmit channels of the external MIDI device.
1) Press [EDIT]. (The indicator will light.)
2) Press [PART] (BANK [3]) several times to select ”Part
MIDI CH.”
3) Press PANEL SELECT [LOWER]/[UPPER] to select
the part that you wish to set.
4) Use [DEC]/[INC] to set the channel.
3 Set the Program Change Transmit/Receive Switch
to BANK SEL + PC.
1) Press [MIDI] (BANK[5]) several times to select “Tx/Rx
ProgChg SW.”
2) Use [DEC]/[INC] to select “BANK SEL + PC.”
* After making the setting, be sure to press [EDIT] or
[EXIT] to make the upper left of the display read “PER-
FORM” or “PATCH.”
4 Transmit a Bank Select MSB (controller number 0)
message to the JP-8080.
5 Transmit a Bank Select LSB (controller number 32)
message to the JP-8080.
6 Transmit a Program Change message to the JP-8080.
* When the JP-8080 receives only a Program Change mes-
sage without receiving Bank Select messages, Patches
within the same group will be selected.
* If a Bank Select message other than those listed in the
table on page 179 is received, that Bank Select message
will be ignored, and Patches will be selected within the
same group.
* If the MIDI channel of each JP-8080 Part has the same
setting as the Performance Ctrl CH (p.124) parameter,
the Performance Ctrl CH setting will take priority,
meaning that the Performance will change when a
Program Change is received.
For the correspondence between the bank select (CC#0,
CC#32) / program numbers (PC#) which are transmitted
and the patches, refer to “Patch List (p.179).”
62
To Next Page
Loading...
