Sanyo PLC-XP200L Service Manual

-43-
Electrical Adjustment
Circuit Adjustments
CAUTION: The each circuit has been made by the fine adjustment at factory. Do not attempt to adjust the following
adjustments except requiring the readjustments in servicing otherwise it may cause loss of performance
and product safety. Before taking these adjustments, turn the projector for more than 10 minutes to sta-
bilize the operation.
[Adjustment Condition]
● Input signal
Analog Computer signal ..... 0.7Vp-p/75W terminated (XGA)
Composite Video signal ... 1.0Vp-p/75W terminated (NTSC / PAL)
Component Video signal .... 0.7Vp-p/75W terminated (480i, 480p, 720p, 1080i)
● Picture control mode .......... “STANDARD” mode unless otherwise noted.
● Lamp mode......................... “Normal” mode unless otherwise noted.
Note:
* Please refer to “Service Adjustment Menu Operation” for entering the service mode and adjusting the service data.
White 100%
Black 100%
16 steps gray scale pattern
W Y C G M R B BK
100% full color bar pattern
z Fan Voltages adjustment
Equipment Digital voltmeter
1. Enter the service mode.
2. Change data values of each test point to adjust the fan
driving voltage.
Group No. Fan Test Point Adjustment value
250 - 0 FN907 TPFN1 5.0 +0.1 -0Vdc
250 - 1 FN907 TPFN1 13.8 +0 -0.1Vdc
250 - 2 FN903 TPFN2
4.0 +0.1 -0Vdc
250 - 3 FN903 TPFN2
13.8 +0 -0.1Vdc
250 - 4 FN905/906 TPFN3 5.0 +0.1 -0Vdc
250 - 5 FN905/906 TPFN3 13.8 +0 -0.1Vdc
250 - 6 FN904 TPFN5 4.5 +0.1 -0Vdc
250 - 7 FN904 TPFN5 13.8 +0 -0.1Vdc
250 - 8 FN902 TPFN6
5.0 +0.1 -0Vdc
250 - 9 FN902 TPFN6 13.8 +0 -0.1Vdc
250 - 10 FN901 TPFN7 5.0 +0.1 -0Vdc
250 - 11 FN901 TPFN7 13.8 +0 -0.1Vdc
250 - 12 FN908 TPFN8 5.0 +0.1 -0Vdc
250 - 13 FN908 TPFN8 13.8 +0 -0.1Vdc
x PC-Auto calibration
Input mode Computer mode
Input signal 16-step gray scale computer signal
1. Enter the service mode.
2. To start the auto-calibration for PC adjustment, select
Group "260", No. "0", and then change data value
"0" to "1".
After the auto-calibration completed, "OK" will appear
on the screen.
c Video-Auto calibration
Input mode Video mode (Composite)
Input signal 100% color bar signal
1. Enter the service mode.
2. To start the auto-calibration for composite-video
adjustment, select Group "260", No. "0", and then
change data value "0" to "1".
After the auto-calibration completed, "OK" will appear
on the screen.

Sanyo PLC-XP200L Specifications

General

Vertical scan range	48 - 100 Hz
Horizontal scan range	15 - 100 kHz
Projection technology	LCD
Projector native resolution	XGA (1024x768)
Keystone correction, vertical	±40 °
Lamp type	NSH
Lamp power	330 W
Light source type	Lamp
Service life of light source	2000 h
Service life of light source (economic mode)	3000 h
Bundled software	User Manual (CD ROM)
I/O ports	DVI-D (digital/HDCP) D-Sub15 (RGB/SCART-RGB) 5 x BNC (RGBHV/Composite/Y-Pb/Cb-Pr/Cr) 3 x RCA (Video/Y-Pb/Cb-Pr/Cr) Mini DIN 4 (S-Video) 3.5 mm Stereo Jack D-Sub15 D-Sub9 (RS232) 3.5 mm Stereo Jack (cable remote control) USB type B
Compatibility	UXGA SXGA SXGA+ WXGA XGA S-VGA VGA Mac
Dimensions (WxDxH)	370 x 440 x 187 mm
Power requirements	100 - 240 V
Power consumption (standby)	24.5 W
Power consumption (typical)	499 W
Storage temperature (T-T)	-10 - 60 °C
Operating temperature (T-T)	5 - 40 °C
Placement	Ceiling

Weight and Dimensions

Weight	11400 g
Package weight	15900 g