Schweitzer Engineering Laboratories SEL-3031 - List of Figures

Date Code 20181001 SEL-3031 Instruction Manual
List of Figures
Figure 1.1 Point-to-Point Product Overview......................................................1.1
Figure 1.2 Point-to-Multipoint Product Overview .............................................1.2
Figure 1.3 Radio Antenna Connections .............................................................1.5
Figure 1.4 SEL-3031 Dimensions......................................................................1.6
Figure 1.5 SEL-3031 Rack Mount (Front and Rear) .........................................1.7
Figure 1.6 SEL-3031 Wall Mount (Front and Rear) ..........................................1.8
Figure 2.1 Fresnel Zone .....................................................................................2.2
Figure 2.2 Antenna Polarization.........................................................................2.6
Figure 2.3 Collocated Antennas With Two Radio Links....................................2.9
Figure 2.4 Three Collocated Synchronized Radios..........................................2.10
Figure 2.5 Wall-Mount and Rack-Mount Rear Connections ...........................2.12
Figure 2.6 SEL-C693 Cable: Two-Wire EIA-485 Connections.......................2.17
Figure 2.7 EIA-232 and EIA-485 DB-9 Connector Pin Numbers ...................2.17
Figure 2.8 SEL-C245A Cable: SEL-3031 to Computer ..................................2.19
Figure 2.9 SEL-C285 Cable: SEL-3031 to DTE Device (SEL Relays)...........2.19
Figure 2.10 SEL-C387 Cable: SEL-3031 to SEL Communications Processor
With IRIG-B ..............................................................................2.20
Figure 2.11 SEL-C273A Cable: SEL-3031 Repeater and Synchronizing
Cable..........................................................................................2.20
Figure 2.12 SEL-C576 Cable: Synchronizing Cable for SEL-3031 ..................2.21
Figure 2.13 USB Interface .................................................................................2.21
Figure 3.1 SEL M
IRRORED BITS Connection Example......................................3.1
Figure 3.2 SEL-3031 Port Settings for MIRRORED BITS Connection ................3.2
Figure 3.3 SEL-351 Port Settings for M
IRRORED BITS Connection ..................3.3
Figure 3.4 SEL-451 Port Settings for MIRRORED BITS Connection ..................3.4
Figure 3.5 SEL-2505 DIP Switch Settings for MIRRORED BITS Connection ....3.5
Figure 3.6 TAR ROKA Command From an SEL-351 .......................................3.5
Figure 3.7 SEL-3031 Linking Information Processors to Relays ......................3.6
Figure 3.8 SEL-3031 Port 1 Settings for Fast Messaging..................................3.7
Figure 3.9 SEL-351 Port Settings for Fast Messaging.......................................3.8
Figure 3.10 Example AUTO Command Output...................................................3.9
Figure 3.11 SEL-3031 Point-to-Multipoint Example ........................................3.10
Figure 3.12 Radio Settings for Point-to-Multipoint ...........................................3.11
Figure 3.13 Port 1 Settings for Point-to-Multipoint...........................................3.12
Figure 3.14 SEL-3530 RTAC DNP3 Settings ....................................................3.13
Figure 3.15 SEL-651R Communications Settings for P2MP ............................3.14
Figure 3.16 SEL-651R DNP Port Settings for P2MP ........................................3.15
Figure 3.17 Setting up Collocated Antennas at a Repeater Location.................3.16
Figure 3.18 SYNC Settings for Master Radio....................................................3.18
Figure 4.1 Communications Menu.....................................................................4.2
Figure 4.2 Serial Port Communications Parameters ..........................................4.3
Preliminary Copy—Subject to Change