Siemens COMOS User Manual

3.5.4 Nominal diameter range of a pipe part...................................................................................40
3.5.4.1 Introduction to nominal diameter ranges................................................................................40
3.5.4.2 Display nominal diameter range.............................................................................................40
3.5.4.3 New calculation of the nominal diameter range.....................................................................41
3.5.4.4 Restricting the nominal diameter range of a pipe part...........................................................42
3.5.4.5 Integration into existing databases.........................................................................................42
3.5.5 Extending a pipe part catalog.................................................................................................43
3.5.5.1 Creating a new catalog..........................................................................................................43
3.5.5.2 Creating a new pipe part........................................................................................................44
3.5.6 "Part description" tab..............................................................................................................44
3.5.7 "Part specification" tab...........................................................................................................45
3.5.7.1 Control group "Pressure/temperature dependency"..............................................................45
3.5.7.2 Control group "Materials – List of objects".............................................................................46
3.5.7.3 Control group "Technical Terms of Delivery".........................................................................46
3.5.8 "Datasheet" tab......................................................................................................................47
3.5.8.1 Control group "Manufacturer data".........................................................................................47
3.5.8.2 Nominal size dependent table................................................................................................47
3.5.9 "Local dimensions (NPS)" tab................................................................................................47
3.5.10 "Text blocks" tab....................................................................................................................49
3.5.11 "Interface codes" tab..............................................................................................................49
3.5.12 "System information" tab........................................................................................................50
3.5.13 "Data maintenance" tab.........................................................................................................50
3.5.14 "Fabrication" tab.....................................................................................................................50
3.5.15 "Comments" tab.....................................................................................................................50
3.5.16 "3D geometry" tab..................................................................................................................50
3.5.16.1 "General" control group..........................................................................................................50
3.5.16.2 "Nominal sizes / connection types" control group..................................................................52
3.5.16.3 "General geometry description" control group.......................................................................52
3.5.17 "Connector <1-n>" tab............................................................................................................52
3.5.18 "Display for nominal diameter range" tab...............................................................................53
3.6 Creating a pipe part type........................................................................................................54
3.6.1 Creating a pipe part type........................................................................................................54
3.6.2 Standard table for function codes..........................................................................................55
3.7 Administering standards.........................................................................................................55
3.7.1 Creating a new system of standards......................................................................................55
3.7.1.1 Overview: Creating a new system of standards.....................................................................55
3.7.1.2 Creating standard tables for a system of standards...............................................................56
3.7.1.3 Extending a system of standards in the "standard geometry tables".....................................57
3.7.1.4 Adding attributes or tabs for the "standard geometry tables".................................................58
3.7.1.5 Extending a system of standards in the pipe part catalog......................................................59
3.7.2 Extending a standard in a system of standards.....................................................................59
3.7.2.1 Creating geometry standards.................................................................................................59
3.7.2.2 Adding values to the geometry tables....................................................................................61
3.7.2.3 Configuring geometry standards for bolts..............................................................................61
3.7.2.4 Configuring geometry standards for nuts and washers..........................................................62
3.8 Preparing bolt sets.................................................................................................................63
3.8.1 Fundamentals of bolt sets......................................................................................................63
3.8.2 Creating a bolt set..................................................................................................................64
3.8.3 Standard tables for bolt parts and bolt sets............................................................................66
Table of contents
PipeSpec Designer
4 Operating Manual, 09/2014, A5E32076948-AA

Siemens COMOS Specifications

General

Manufacturer	Siemens
Description	COMOS is plant engineering software for the process industry. It manages plant projects and documentation. It covers the entire plant lifecycle from engineering and design to operation and maintenance.
Functionality	Plant design and engineering
Integration	Integrates with Siemens TIA Portal, SIMATIC PCS 7, and other third-party systems
Data Management	Centralized data management
Modules	Includes modules for process engineering, electrical engineering, instrumentation, and automation
Collaboration	Supports multi-disciplinary team collaboration with role-based access
Documentation	Automated generation of documentation (e.g., P&IDs, loop diagrams, instrument lists), document management, version control.
Customization	Highly customizable to meet specific project requirements and industry standards. Allows for scripting and API integration.
Industry Standards	ISO, IEC