Siemens SINAMICS S150 - Page 8

Table of contents
Drive converter cabinet units
8 Operating Instructions, 07/07, A5E00288214A
4.7 External supply of the auxiliary supply from a secure line .......................................................... 59
4.8 Signal connections ...................................................................................................................... 60
4.8.1 Customer terminal block (-A60) .................................................................................................. 60
4.9 Other connections....................................................................................................................... 67
4.9.1 dV/dt filter with Voltage Peak Limiter (option L10)...................................................................... 67
4.9.2 Sinusoidal filter (option L15)........................................................................................................ 69
4.9.3 Connection for external auxiliary equipment (Option L19).......................................................... 71
4.9.4 Main switch incl. fuses or main circuit breaker (option L26) ....................................................... 73
4.9.5 EMERGENCY STOP pushbutton (option L45)........................................................................... 74
4.9.6 Cabinet illumination with service socket (option L50) ................................................................. 75
4.9.7 Cabinet anti-condensation heating (option L55) ......................................................................... 76
4.9.8 EMERGENCY STOP category 0; 230 V AC or 24 V DC (option L57) ....................................... 77
4.9.9 EMERGENCY STOP category 1; 230 V AC (option L59) .......................................................... 78
4.9.10 EMERGENCY STOP category 1; 24 V DC (option L60) ............................................................ 79
4.9.11 25 kW braking unit (option L61/L64); 50 kW braking unit (option L62/L65)................................ 80
4.9.11.1 Installing the braking resistor ...................................................................................................... 80
4.9.12 Thermistor motor protection unit (option L83/L84)...................................................................... 86
4.9.13 PT100 evaluation unit (option L86) ............................................................................................. 87
4.9.14 Insulation monitor (option L87) ................................................................................................... 89
4.9.15 Communication Board Ethernet CBE20 (option G33) ................................................................ 90
4.9.16 SMC10 Sensor Module for determining the actual motor speed and the rotor position
angle (option K46)....................................................................................................................... 92
4.9.16.1 Description .................................................................................................................................. 92
4.9.16.2 Connection .................................................................................................................................. 93
4.9.16.3 Connection example ................................................................................................................... 94
4.9.17 SMC20 Sensor Module for determining the actual motor speed and the path length
(option K48)................................................................................................................................. 96
4.9.17.1 Description .................................................................................................................................. 96
4.9.17.2 Connection ...........................................................................................................
....................... 97
4.9.17.3 Connection example ................................................................................................................... 98
4.9.18 SMC30 Sensor Module for detecting the actual motor speed (option K50) ............................. 100
4.9.18.1 Description ................................................................................................................................ 100
4.9.18.2 Connection ................................................................................................................................ 103
4.9.18.3 Connection examples................................................................................................................ 105
4.9.19 Voltage Sensing Module for determining the actual motor speed and the phase angle
(option K51)............................................................................................................................... 106
4.9.20 Customer terminal block extension (option G61)...................................................................... 106
4.9.21 Terminal module for activation of "Safe Torque Off" and "Safe STOP 1" (option K82)............ 107
4.9.22 NAMUR terminal block (option B00) ......................................................................................... 111
4.9.23 Electrically separate 24 V DC power supply for NAMUR (option B02)..................................... 113
4.9.24 Outgoing section for external auxiliary equipment for NAMUR (option B03)............................ 113
5 Commissioning ...................................................................................................................................... 115
5.1 Chapter content......................................................................................................................... 115
5.2 STARTER commissioning tool.................................................................................................. 116
5.2.1 Installing STARTER .................................................................................................................. 116
5.2.2 The STARTER user interface ................................................................................................... 117
5.3 Procedure for commissioning via STARTER............................................................................ 118
5.3.1 Creating a project...................................................................................................................... 118
5.3.2 Configuring the drive unit .......................................................................................................... 127
5.3.3 Starting the drive project ........................................................................................................... 153
5.3.4 Connection via serial interface.................................................................................................. 154
5.4 The AOP30 operator panel ....................................................................................................... 157