Siemens SINUMERIK 840DE

Index
Fundamentals
Index-2 Programming Manual, 10.2004 Edition, 6FC5 298-7AB00-0BP1
C
C, 3-10, 7-2
CALCPOSI, 3-31, 12-59
CDOF, 8-58
CDOF2, 8-58
CDON, 8-58
CFC, 7-33
CFCFGROUP, 4-38
CFIN, 7-33
CFTCP, 7-33
Chamfer, 4-71
Chamfer the contour corner, 4-72
Change of direction, 8-39
Channel axes, 1-25
Character set, 2-2
CHF, 4-72
CHR, 4-72
CIP, 4-17, 4-30
Circle
Circle radius CR, 2-7
Circle radius CR, 2-8
Circular interpolation
Helical interpolation, 4-36
Indication of working plane, 4-23
Programming a circle with intermediate and end
points, 4-16, 4-30
Programming a circle: with tangential
transition, 4-16
Programming a circle: Input in incremental or
absolute dimensions, 4-27
Programming a circle: with arc angle and center
point, 4-16, 4-26
Programming a circle: with center and end
points, 4-16, 4-20
Programming a circle: with polar angle and polar
radius, 4-16
Programming a circle: with polar coordinates, 4-
28
Programming a circle: with radius and end
point, 4-16, 4-24
Circular magazine, 8-17
Clamping torque FXST, 4-69
COARSEA, 7-14
Collision Detection ON (CDON)/OFF (CDOF), 8-58
Collision monitoring, 8-58
Collisions, 8-35
Command axes, 1-27
Comments, 2-19
Compensation plane, 8-63
Constant
cutting rate, 7-37
Grinding wheel peripheral speed, 7-41
Constants, 2-16
Binary constants, 2-16
Hexadecimal constants, 2-16
Integer constants, 2-16
Continuous-path mode, 5-5, 5-7
Look ahead, 5-14
with programmable transition rounding, 5-8
Contour
damage, 8-61
point, 8-32
Roughing, 2-19
Contour accuracy, programmable, 5-22
Coordinate systems, 1-1
Absolute dimensions, 1-5
Basic Coordinate System, 1-15
Incremental dimension, 1-7
Machine coordinate system, 1-12
Overview, 1-11
Plane designations, 1-8
Polar coordinates, 1-5
Workpiece coordinate system, 1-17
Coordinate systems and workpiece machining, 1-30
Coordinate systems of active machining
operation, 8-75
Corner behavior
Intersection, 8-41
Transition circle, 8-40
CORROF, 6-40, 6-41
CR, 2-8, 3-13, 4-39
CROTS, 6-25
CT, 4-17, 4-33
CUT2D, 3-28, 8-5, 8-61, 8-64
CUT2DF, 3-28, 8-5, 8-61, 8-64
Cutting rate, constant, 7-39, 7-40
Cylinder surface curve transformation, 7-21
Cylinder thread, 4-51
D
d, 7-22
D, 2-5, 8-16, 8-19, 8-20
D0, 8-15, 8-16
Data types, 2-15
Constants, 2-16
DC, 3-11, 7-14
Deactivate compensation mode
G40, 8-35
G40, KONT, 8-37
Definition of workpiece positions, 1-2
DELDL, 8-71
Deselect frame, 6-38
destination, 10-4, 10-6
DIAM90, 3-16
DIAMOF, 3-16