Siemens SINUMERIK 840DE - Page 508

Index
Fundamentals
Index-6 Programming Manual, 10.2004 Edition, 6FC5 298-7AB00-0BP1
M30, 9-5, 11-1, 11-5
M4, 4-48, 7-13, 7-34, 7-35, 9-5
M40, 9-5
M41, 7-13, 9-5
M42, 9-5
M43, 9-5
M44, 9-5
M45, 7-13, 9-5
M5, 7-13, 7-34, 7-35, 9-5
M6, 8-14, 9-5
M7, 9-3
M70, 7-14, 9-5
Machine axes, 1-24
Machine coordinate system, 1-12
Main axes, 1-23
Main block, 2-8
Main spindle, 1-24
Make active tool offset operative immediately, 8-22
Master spindle, 1-24
MEAS, 3-16
MEAW, 3-16
Messages, 2-19
MIRROR, 6-2, 6-5, 6-29
Miscellaneous function (M), 2-5, 2-7
Modal feedrate, 4-72
Modal rounding, 4-72
Monitoring window FXSW, 4-69
Motion commands, 4-1
Number of axis values, 4-2
Programming Motion Commands, 4-1
Start point - destination point, 4-2
MSG, 2-19
Multiple feedrate values in one block, 7-43
N
N, 2-5, 2-7, 10-3
Names, 2-13
Array identifiers, 2-15
Identifier, 2-14
Variable identifiers, 2-15
New p72lp, 5-19
Non-cutting tool path, 8-42
Non-linear interpolation, 4-12
Non-modal feedrate, 4-72
NORM, 8-32, 8-38
O
OFFN, 8-23
Offset memory, 8-65
Operators, 2-12
ORIPATH, 12-14
OVR, 2-7, 7-26
OVRA, 7-26
P
P, 2-7
Parameterizing cycle alarms, 2-20
PAROT, 6-36
PAROTOF, 6-36
Path action, depending on DISC values, 8-41
Path axes
traverse with handwheel override, 7-28
Path axes, 1-25
Path override OVR, 2-7
Path tangent, 8-36
Plane designations, 1-8
PLC axes, 1-27, 1-28
PM, 8-44
Polar
-angle AP, 2-8
Polar coordinates, 1-5, 4-5
Define pole, 4-4, 4-5
Polar angle AP, 4-9
Polar radius RP = 0, 4-9
POLF, 4-64
POLFMASK, 4-64
POLFMLIN, 4-64
POS, 2-7, 7-9, 7-25
POSA, 2-7, 7-9
Position-controlled spindle operation, 7-11
Position-controlled spindles, position
Position a spindle from standstill, 7-19
Position spindle from rotation, 7-12
Positioning axes
traverse, 7-9
Positioning axis POS, 2-7
POSP, 7-9
PR, 8-44
Preparatory function G, 2-7
Preprocessor stop, 7-11
Program
-identifiers, 2-1
Programming messages, 2-19
Setting alarms, 2-20
Program jumps, conditional, 10-5
Program jumps, unconditional, 10-3
Program passes, number P, 2-7
Program repetition, 11-6
Program section, 2-17
Program section repetition, 11-7
Programmable contour accuracy, 5-22
Programmable frame rotations with solid angles, 6-
24