Siemens SINUMERIK 840DE

Index
Fundamentals
Index-8 Programming Manual, 10.2004 Edition, 6FC5 298-7AB00-0BP1
Statement list, 12-1
Straight line with angle, 4-43
String variable, 10-4, 10-6
Subblock N, 2-7
Subprogram list, 12-44
Subprogram, call, 11-4
Subprograms, 11-1
Program repetition, 11-6
Subroutine
-call L, 2-7
SUPA, 3-21, 6-39
Synchronized axes, 1-26
T
T, 2-5, 2-8, 2-9
T0, 8-12, 8-14
Taper thread, 4-52
Tapping
Rigid tapping, 4-57
with compensating chuck, 4-59
Without compensating chuck:right-hand/left-
hand threads, 4-58
TCARR, 8-64
TCOABS, 8-64
TCOFR, 8-64
TCOFRX, 8-64
TCOFRY, 8-64
TCOFRZ, 8-64
Technology G groups, 5-19
Thread chains, 4-48
Thread cutting, 4-47, 4-51, 4-61
Cylinder thread, 4-51
Right-hand/left-hand threads, 4-48
Start point offset, 4-53
Taper thread, 4-52
Thread chains, 4-48
with constant lead, 4-47, 4-51
with linearly progressive/degressive speed
change, 4-56
TMOF, 8-67
TMON, 8-67
TOFRAME, 6-35
TOFRAMEX, 6-35
TOFRAMEY, 6-35
TOFRAMEZ, 6-35
Tool
-number T, 2-8
Offset number D, 2-5
Tool change point, 8-35
Tool edge number D, 2-7
Tool edge reference point, 8-79
Tool length
compensation:from toolholder orientation,
TCOABS, 8-65
component, 8-64
offset, 8-63
Tool monitoring
Deactivate, 8-67
Selection/deselection, 8-67
Tool offset
Coordinate system for wear values, 8-75
Tool offset, CUT2D, CUT2DF, 8-61
Tool offsets
Compensation at outside corners, 8-38
Smooth approach and retraction (SAR), 8-42
Tool radius compensation, 8-5
Tool radius compensation, 8-23, 8-71
Changing:direction of compensation, 8-30
Changing:offset number D, 8-30
Corner behavior:Intersection, 8-41
Corner behavior:Transition circle, 8-40
CUT2D, 8-62
CUT2DF, 8-62
Tool T, 2-5
Tool types, 8-6, 8-66
Toolholder, 8-64
Tools with a relevant tool point direction, 8-79
TOROT, 6-35
TOROTOF, 6-35
TOROTX, 6-36
TOROTY, 6-36
TOROTZ, 6-36
TOWBCS, 8-77
TOWKCS, 8-77
TOWMCS, 8-77
TOWSTD, 8-77
TOWTCS, 8-77
TOWWCS, 8-77
TRAANG, 7-22
TRACYL, 7-20, 7-22
TRAFOOF, 3-32, 6-40, 7-20, 7-22
TRANS, 3-13, 6-2, 6-8, 6-12, 10-1
Transformation, 7-19
Transformation TRACYL, 7-22
Transformation TRAORI, 6-40
Transition
circle, 8-40, 8-60
ellipsis/parabola/hyperbola, 8-41
radius, 8-39
Transition current/next block, 8-36
TRANSMIT, 7-20
TRANSMIT transformation, 7-20
Transverse axis
coordinate system, 3-17
Dimensioning for transverse axis, 3-15
Zero points, 3-17