Simplex 4010ES IDNAC - Standalone System Layout

84 pages

To Next Page

To Previous Page

page 5 579-1150 Rev M

4010ES IDNAC Fire Alarm System Installation Guide

2.1.1 Standalone system layout

Figure 1 shows the layout of the 4010ES standalone configuration.

Figure 1: Standalone 4010ES system

Main Page

Table of Contents3
Cautions, Warnings, and Regulatory Information5
Overview6
Standalone Configuration6
Standalone System Layout7
Network Configuration8
Connecting Network Loops (4120 Network Only)9
Net Network Configurations9
4120 Network Communication11
Net Network Communication11
Basic Hardware12
Cpu12
CPU Leds14
CPU Jumper Settings15
CPU Switches15
CPU Connectors/Ports/Terminal Block16
CPU Card Specifications16
Operator Interface17
Extended System Supply18
ESS Leds19
ESS Jumpers20
Specifications21
48-LED Module23
48-LED Module Specifications24
System Power24
Backup Batteries24
Panel Configurations25
One-Bay 4010ES Panels25
Optional Modules26
Back Box Mechanical Specifications28
Two-Bay 4010ES Panels28
Optional Modules31
Back Box Mechanical Specifications31
Available Panels and Devices32
Panels32
Optional Modules34
Local Optional Modules34
Remote Devices35
Adjunct Features35
End User Programming Tools35
LED Kits for the 48-LED Module36
Installing 4010ES Systems37
Mounting the Panel37
Installing the Back Box37
Attaching the Dead Front38
Dead Front Grounding Straps39
Attaching Doors40
General Field Wiring Guidelines40
Connecting 4010ES Basic Components42
Connecting the CPU and the Operator Interface42
Connecting the ESS44
Connecting the 48-LED Module46
RUI Wiring47
Installing the Optional Modules49
Installing One-Block and Two-Block Cards49
Address Configuration DIP Switch50
Connecting Main System Power51
Panel Power-Up Sequence53
ESS Field Wiring54
ESS Idnet Wiring54
Wiring Parameters54
Class a Wiring55
Class B Wiring56
Class X Wiring56
ESS IDNAC Wiring56
Device Wiring Guidelines57
Ferrite Beads57
Class B Wiring Tables57
Class B Wiring to Devices59
Calculating Class B Wiring with Isolators59
ESS AUX/NAC Wiring60
ESS Auxiliary Relay Wiring Guidelines62
PC Software Connections63
Software Modes63
Ethernet Service Port64
System Wiring Checkout and Earth Fault Diagnostics65
Checking System Wiring65
Meter Readings65
Earth Fault Diagnostics66
General Guidelines66
Earth Fault Searching from the Front Panel66
Access Level Selection66
Starting the Earth Fault Search67
Search Option A: Select Location67
Search Option B: Select Location67
Search Option C: Last Search Result68
Completing the Search68
Earth Fault Search Results68
Non-Point Faults68
Point Faults68
Fault Not Found68
No Fault69
Result Not Available69
10 Appendix A: ULC Programming Requirements70
Common Earth Fault Ground Indicator70
Step 1. Open CPU Card Properties Dialog70
Step 2. Program the LED71
Simultaneous Alarm Display71
Creating Annunciation Zone Lists71
Programming the Address and Mode for each LED72
Setting Alarm Verification Timer to Canadian Operation73
Procedure73
Setting Alarm Reset/Inhibit Timer74
Enabling Alarm Reset/Inhibit Timer74
Alarm Cutout Timer75
Enabling Alarm Cutout Timer75
11 Appendix B: UL Programming Requirements77
Setting Alarm Verification to US Operation77
Procedure77
Alarm Cutout Timer77
Enabling Alarm Cutout Timer78
Non-Steady Visual Evacuation System Option78
Appendix C: Simplex Special Application Appliances and Accessories80
13 Appendix D: IDNAC Compatible Appliances81

Simplex 4010ES IDNAC - Standalone System Layout

Table of Contents

Related product manuals