Sony XVS-G1

398
For a Flexi Pad control block, transition control
block, transition control block (simple type),
independent key transition control block
Select the target switcher bank to set.
In the [Select Bank] group, pla
ce a check mark for the
switcher bank to select.
By default, the switcher ba
nk where the selected
control block is located in the full view is selected.
You can also select multiple sw
itcher banks and set
assignable buttons simultaneously.
• When multiple switcher banks are selected, the last
sele
cted switcher bank becomes the reference and
is displayed highlighted. The button names
configured on the reference switcher bank are
displayed on the assignable buttons.
When the reference switcher bank is deselected, the
re
ference will be set according to the following
order of priority.
M/E-1 > M/E-2 > M/E-3 > M/E-4 > M/E-5 > P/P
• In multi program 2 mode, main and sub can be set
sepa
rately. When a switcher bank is set to shared
main and sub, the assignable button assignments
are also shared.
3 Press the target assignable button to set.
The [Select Function] wi
ndow appears.
The functions that can be assigned to the selected
bu
tton are displayed in the [Select Function] window.
For an independent key transition
control block
Select a tab to change the function to display.
[Current] tab:
Keys of the switcher bank where the
selected control block is located
[Other banks] tab:
Keys of the switcher banks other
than the switcher bank where the selected control
block is located
4 Set the button for the function to assign to the on
state.
To release a function assignment
Set the [No Assign] button to the on state.
5 Press [OK].
To set the fader lever in a key fader control block
You can set the key which is the target of fader lever
operat
ion.
Press the button at the bottom of the fader lever to display
the [Sele
ct Function] window.
Set the button for the target key to the on state and press
[O
K].
All: Enable
operation for all four keys assigned to key
delegation buttons.
Disable:
Disable fader lever operation.
Key delegation 1: Enabl
e operation for the key assigned
to key delegation button 1.
Key delegation 2: Enabl
e operation for the key assigned
to key delegation button 2.
Key delegation 3: Enabl
e operation for the key assigned
to key delegation button 3.
Key delegation 4: Enabl
e operation for the key assigned
to key delegation button 4.
The name of the keys assigned to the key delegation
bu
ttons are displayed for key delegation 1 to 4 above.
To return assignable button assignments to the
defaults
Press the [Default Recall] button, check the message, then
press [OK].
The assignable button assignments and fader lever
set
tings return to the defaults.
Assigning regions to a region selection
button in the numeric keypad control
block
You can assign up to four regions to each region selection
button.
When multiple regions are assign
ed, the region name set
for the lowest number is displayed on the region selection
button.
1 Open the Home > Setup > Panel > Module > Button
Assign menu (19104.21).
2 Press within the white frame of the target numeric
keypad control block to set.
An enlarged image of the nu
meric keypad control
block appears.
3 Press the target assignable button to set.
The [Select Function] window for
selecting a region
number appears.
4 Press the [Edit] button for the target region number (1
to 4) to set.
The [Select Function] window for
selecting a region
appears.
Select a tab to change the region to display.
[ME/DME] tab:
Switcher bank and DME regions
[Dev/Macro] tab:
External device and macro regions
[User] tab: U
ser regions
5 Set the button for the region to assign to the on state.
To release the region assignment
Set the [No Assign] button to the on
state.
Notes
Note