2-4
dummyheaddummyhead
SERVICE INFORMATION
FRAME
Unit: mm (in)
ENGINE & FRAME TORQUE VALUES
Use standard torque values for fasteners that are not listed in this table.
ENGINE
Part Item Standard Service limit
EMT sensor Resistance 40°C/104°F 1.0 – 1.3 kΩ –
100°C/212°F 0.1 – 0.2 kΩ –
VTEC spool
solenoid valve
Resistance
14.25 – 15.75 Ω –
IAC valve Resistance 8.7 – 10.5 Ω –
HO2S heater Resistance 4 – 30 Ω –
Part Item Standard Service limit
Vertical shaft Shaft O.D. (at needle bearing) 30.491 – 30.500 (1.2004 – 1.2008) 30.470 (1.1996)
Runout LA type 0.30 (0.012) or below 0.30 (0.012)
XA and XCA types 0.35 (0.014) or below 0.35 (0.014)
XXA and XXCA types 0.40 (0.016) or below 0.40 (0.016)
Bushing I.D. 17.02 – 17.13 (0.670 – 0.674) 17.65 (0.695)
Propeller shaft Shaft O.D. (at needle bearing) 32.007 – 32.020 (1.2601 – 1.2606) 31.990 (1.2594)
Shaft O.D. (at bevel gear) 27.974 – 27.983 (1.1013 – 1.1017) 27.949 (1.1004)
Runout 0.02 (0.001) or below 0.02 (0.001)
Propeller/gear
case/extension
case
Forward bevel gear backlash 0.30 – 0.54 (0.012 – 0.021) –
Reverse bevel
gear backlash
Standard rotation 0.40 – 0.65 (0.016 – 0.026) –
Counter rotation 0.41 – 0.64 (0.016 – 0.025) –
Thrust clearance adjustment 0.20 – 0.40 (0.008 – 0.016) –
Power trim/tilt
assembly
Lower chamber blow pressure 8,826 – 11,768 kPa (90 – 120 kgf/
cm
2
, 1,280 – 1,707 psi)
–
Upper chamber blow pressure 3,923 – 7,355 kPa (40 – 75 kgf/cm
2
,
569 – 1,067 psi)
–
Power tilt motor
assembly
Brush length 9.8 (0.39) 4.8 (0.19)
Mica depth – 0.50 (0.020)
Item
Thread Dia. and pitch Torque values
Remarks
mm (in) N·m kgf·m lbf·ft
Bearing cap bolt (11 x 105 mm) M11 x 1.5 – – – See page 15-21
Side bolt (10 x 60 mm) M10 x 1.25 49 5.0 36
Side bolt (10 x 80 mm) M10 x 1.25 49 5.0 36
Side bolt (10 x 109 mm) M10 x 1.25 49 5.0 36
Timing belt back cover (CMP
sensor) bolt M5 x 0.8 3.9 0.40 2.9
Cylinder head bolt/washer M12 x 1.5 – – – See page 14-24
Spark plug M14 x 1.25 18 1.8 13
Valve adjusting nut M7 x 0.75 20 2.0 15 Apply engine oil to the
threads and seating
surface.
Connecting rod bolt M8 x 0.75 – – – See page 15-20
Crankshaft pulley bolt M16 x 1.5 245 25.0 181 See page 14-14
Timing belt idler pulley A bolt M12 x 1.25 83 8.5 61
Timing belt idler pulley B bolt M10 x 1.25 39 4.0 29 ALOC bolt; replace
with a new one.
Timing belt tensioner bolt M10 x 1.25 39 4.0 29
Timing belt tensioner base bolt M10 x 1.25 45 4.6 33
Timing belt driven pulley bolt M12 x 1.25 90 9.2 66 Apply engine oil to the
threads and seating
surface.
Rocker arm shaft (IN side) bolt M8 x 1.25 24 2.4 18
Rocker arm shaft (EX side) bolt M8 x 1.25 24 2.4 18 Apply engine oil to the
threads and seating
surface.
To Next Page
