Need help?Do you have a question about the Topcon MC-X1 and is the answer not in the manual?
General| Brand | Topcon |
|---|---|
| Model | MC-X1 |
| Category | Touch Panel |
| Language | English |
Lists hardware and software components for the 2D and 3D excavator indicate systems.
Describes methods to access the MC-X1 web interface via PC or MCXCONFIG for configuration.
Explains how to view general information and upgrade MC-X1 firmware through the web interface.
Details the procedure for upgrading the MC-X1 controller's firmware via the web interface.
Details the procedure for resetting MC-X1 settings to default values to resolve unknown states.
Guides on configuring the GR-i3 vibration mount as an auxiliary antenna within the system.
Outlines the steps to load firmware onto the GR-i3 GNSS antenna using the MC-X interface.
Details the process for loading GNSS firmware onto the GR-i3 using the firmware upgrade tabs.
Describes how to verify CAN communication and check connected devices in the system.
Explains how to configure radio channels for the EASy-Proof radio using 3D-MC.
Provides steps for performing a factory reset on the GR-i3 using the Topcon Receiver Utility.
Details the configuration process for the optional SL-100 for communication with the MC-X1.
Provides important notes and cautions for installing TS-i3 tilt sensors on the excavator.
Explains how to correctly orient TS-i3 sensors for proper measurement and calibration.
Details the correct procedure for terminating the CAN bus to ensure proper communication.
Describes the mounting process for the hitch sensor, highlighting challenges and best practices.
Presents an optional mounting location for the hitch sensor on the DogBone for added protection.
Explains the mounting differences and procedures for installing a tilt bucket sensor.
Lists supported brands of tilting/rotating attachments and notes the need for manufacturer-specific documentation.
Guides on locating a convenient surface and mounting the stick sensor on the excavator stick.
Details how to mount the boom sensor parallel to the boom center, avoiding tapered sections.
States that secondary boom sensor mounting is identical to primary boom sensor locations.
Describes mounting the TS-i3d dual axis body sensor on the excavator body.
Explains mounting the LS-B10W Laser Receiver and bracket on the left side of the stick.
Instructs on installing the MC-X1 Controller onto the machine's body using magnet mounts.
Details the process of welding the antenna pole mount and installing the GNSS antenna.
Guides on installing the WiFi Antenna Magnet Mount and antenna onto the machine's cab.
Explains accurately measuring and entering machine dimensions into the 3D-MC machine builder.
Guides on setting up the machine file and selecting excavator options for sensor input.
Details assigning sensors to corresponding machine elements by selecting serial numbers.
Explains configuring tone and duration settings for audible guidance alerts.
Describes entering desired settings for the light bar indicators on the display.
Indicates the completion of the machine configuration process and saving the file.
Explains how to adjust the filter level for each sensor to control reaction speed.
Details the process of calibrating the body sensor, including pitch and roll.
Guides on calibrating the boom sensor, recommending a laser for zero degree positioning.
States that the secondary boom sensor uses the same calibration method as the primary boom sensor.
Explains how to position the stick at -90 degrees for stick sensor calibration.
Covers mounting options for the hitch sensor, introducing DogBone and quick-release.
Details the calibration procedure for the DogBone sensor, requiring stick sensor calibration first.
Describes the calibration procedure for the hitch sensor when mounted on the hitch or quick-coupling.
Outlines procedures for attachment edge calibration for all attachment types.
Guides on calibrating multiple attachments, emphasizing vertical and flat calibrations for each.
Explains how to enter tilt bucket measurements and calibrate its orientation.
Details determining the LS-B10W position and calibrating its angle relative to the stick.
Lists general and environmental specifications for the MC-X1 controller.
Provides detailed pinout information for the MC-X1 connectors (Conn A and Conn B).
Lists general, environmental, physical, and signal tracking specifications for the GR-i3.
Details specifications for the BLACK OMNI ANTENNA, 2.4-2.5 GHZ WI-F1.
Lists specifications for the HIGH FREQ NMO MAG MOUNT 0-6GHZ.
Provides essential safety warnings and precautions for operating and installing the equipment.
Advises on safe installation distances to comply with RF exposure requirements.
Covers FCC and IC statements, including compliance and device operation conditions.
Details FCC compliance rules and conditions for device operation.
Details Canadian compliance rules and conditions for device operation.
Specifies the input voltage and functional range for the system components.
Directs users to the Topcon TotalCare website for open source software licenses and notices.
To Next Page
