Toshiba B-EX4T2 SERIES - Dump Mode Setting

2. PRINTER SETUP ENGLISH VERSION EO1-33094
2.6 Printer Setting
E2-28
2.6.7 Dump Mode Setting
(Cont.)
The data in the receive buffer is printed as follows.
Receive Buffer Size
Interface B-EX4T2-GS/TS/HS
RS-232C 1MB (65536 lines)
Centronics 1MB (65536 lines)
LAN 1MB (65536 lines)
BASIC 1 8KB (512 lines)
BASIC 2 8KB (512 lines)
USB 1MB (65536 lines)
RFID 8KB (512 lines)
Required Media Length
Interface B-EX4T2-GS/TS B-EX4T2-HS
RS-232C 198.2 m 198.6 m
Centronics 198.2 m 198.6 m
LAN 198.2 m 198.6 m
BASIC 1 2 m 2 m
BASIC 2 2 m 2 m
USB 198.2 m 198.6 m
RFID 2 m -
*: Media length required for printing all data in the receive buffer.
:
:
:
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
7B 41 58 3B 2B 30 30 30 2C 2B 30 30 30 2C 2B 30 {AX;+000,+000,+0
30 7C 7D 7B 44 30 37 37 30 2C 31 31 30 30 2C 30 0|}{D0760,1100,0
37 34 30 7C 7D 7B 43 7C 7D 7B 4C 43 3B 30 30 33 740|}{C|}{LC;003
30 2C 30 30 32 30 2C 30 30 33 30 2C 30 36 36 30 0,0020,0030,0660
2C 30 2C 32 7C 7D 7B 4C 43 3B 30 30 37 30 2C 30 0,2|}{LC;0070,0
30 32 30 2C 30 30 37 30 2C 30 36 36 30 2C 30 2C 020,0070,0660,0,
39 7C 7D 7B 4C 43 3B 30 30 35 30 2C 30 30 32 30 9|}{LC;0050,0020
:
:
:
44 45 46 47 48 49 4A 7C 7D 7B 50 43 31 30 3B 30 DEFGHIJ|}{PC10;0
33 35 30 2C 30 34 30 30 2C 31 2C 31 2C 4B 2C 30 350,0400,1,1,K,0
30 2C 42 3D 41 42 43 44 65 66 67 68 69 6A 6B 6C 0,B=ABCDefghijkl
6D 6E 6F 70 7C 7D 7B 50 56 30 32 3B 30 33 33 30 mnop|}{PV02;0330
2C 30 36 36 30 2C 30 32 37 30 2C 30 32 35 30 2C 0660,0270,0250,
41 2C 30 30 2C 42 3D 42 7C 7D 7B 50 56 30 33 3B A,00,B=B|}{PV03;
:
:
:
3B 30 39 30 30 2C 30 31 38 30 2C 54 2C 48 2C 30 ;0900,0180,T,H,0
35 2C 41 2C 30 3D 31 32 33 34 35 36 37 38 39 30 5,A,0=1234567890
41 42 43 44 45 7C 7D 00 00 00 00 00 00 00 00 00 ABCDE|}.........
:
:
:
Print Conditions
• Printing width: 3.9 inches
(Approx. 100 mm)
• Sensor selection: None
• Print speed: 6”/sec. (203 dpi)
5”/sec. (300 dpi)
3”/sec. (600dpi)
• Printing mode: Depends on
the selection in use.
• 16 bytes/line
• Data is printed in the order
from the new one to the old.
• Data specified by the receive
buffer write pointer will be
printed in boldface.
NOTE:
If an error occurs while
printing, the printer stops
printing and shows an error
message.
To clear the error, press the
[PAUSE].
After clearing the error the
printer does not resume
printing automatically.