e-STUDIO2008A/2508A/3008A/3508A/4508A/5008A © 2015 TOSHIBA TEC CORPORATION All rights reserved
ERROR CODE AND TROUBLESHOOTING
8 - 20
CC01 Finisher related
service call
A model not supporting the Finisher is connected. Note
that this error is recognized in the communication
converter and is output.
-
CC02 Stack exit roller nip home position detection error: The
detection of the home position of the stack exit roller nip
ends abnormally. [MJ-1032/MJ-1033]
P. 8-203
CC20 Saddle communication error [MJ-1106/1108] P. 8-203
CC21 The detection of the home position of the saddle stitch
3rd transport roller drive motor ends abnormally.
P. 8-204
CC22 The detection of the home position of the saddle stitch
stapler unit ends abnormally.
P. 8-205
CC23 An abnormal interruption of the encoder pulse of the
folding blade occurs.
-
CC30
Stack transport motor abnormality: The stack transport
motor is not rotating or the stack transport belt is not
moving normally. [MJ-1101/1107/MJ-1106/1108]
P. 8-205
CC31 Transport motor abnormality: The transport motor is not
rotating or the stack transport roller -1 and -2 is not
rotating normally. [MJ-1101/1107/MJ-1106/1108]
P. 8-206
CC41 Paper holder cam home position abnormality: The paper
holder cam is not at the home position. [MJ-1101/1107]
P. 8-207
CC51 Sideways adjustment motor (M2) abnormality: Sideways
adjustment motor is not rotating or puncher is not shifting
normally. [MJ-1101/1106 (when MJ-6103 is installed), MJ-
1107/1108 (when MJ-6104 is installed)]
P. 8-207
CC52 Skew adjustment motor (M1) abnormality: Skew
adjustment motor is not rotating or puncher is not shifting
normally. [MJ-1101/1106 (when MJ-6103 is installed), MJ-
1107/1108 (when MJ-6104 is installed)]
P. 8-209
CC53 An abnormality occurs in the punch waste full sensor. P. 8-209
CC54 Hole punch registration sensor detection error: An
abnormality occurs in the hole punch registration sensor.
[MJ-1032/MJ-1033]
P. 8-210
CC60 Punch motor abnormality: Punch motor is not rotating or
puncher is not shifting normally.]
P. 8-212
CC61 Punch motor (M3) home position detection error: Punch
motor is not rotating or puncher is not shifting normally.
[MJ-1101/1106 (when MJ-6103 is installed), MJ-1107/
1108 (when MJ-6104 is installed)]
P. 8-212
CC71 Punch ROM checksum error: Abnormality of checksum
value on Hole punch controller PC board is detected
when the power is turned on. [MJ-1101/1106 (when MJ-
6103 is installed), MJ-1107/1108 (when MJ-6104 is
installed)]
P. 8-213
CC72 Punch RAM read/write error: Abnormality of checksum
value on Hole punch controller PC board is detected
when the power is turned on. [MJ-1101/1106 (when MJ-
6103 is installed), MJ-1107/1108 (when MJ-6104 is
installed)]
P. 8-213
CC80 Rear alignment motor abnormality: The rear alignment
motor is not rotating or the rear alignment plate is not
moving normally. [MJ-1101/1107/MJ-1106/1108]
Rear alignment plate home position detection error: The
detection of the home position ends abnormally because
the rear alignment plate has not worked properly.
[MJ-1032/MJ-1033]
P. 8-214
Error code Classification Contents Troubleshooting
To Next Page
Loading...
