8
© 2015 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2008A/2508A/3008A/3508A/4508A/5008A
ERROR CODE AND TROUBLESHOOTING
8 - 21
CC91 Finisher related
service call
The detection of the home position of the gripper arm
ends abnormality.
P. 8-137
CC92 The movable tray exceeds its upper limit. P. 8-215
CC93 Knurled roller shift solenoid abnormality: An abnormality
occurs in the knurled roller shift solenoid. [MJ-1032]
P. 8-216
CC94 1st fan motor abnormality: The 1st fan motor is locked
abnormally. [MJ-1032]
P. 8-216
CCF1 Tray safety switch abnormality -
The tray safety switch turned on during tray operation
(moving up or down).
-
CDE0 Paddle motor abnormality: The paddle motor does not
rotate properly.
P. 8-216
CDF0 Offset tray related
service call
Initialization error of the offset tray: The home position of
the separator cannot be detected when the power is
turned ON.
P. 8-218
CE00 Optional
communication
related service call
Communication error between finisher unit and puncher
unit: Communication error between the finisher controller
PC board and punch controller PC board.
P. 8-178
CE50 Process related
service call
Temperature/humidity sensor abnormality: The output
value of this sensor is out of a specified range.
P. 8-167
CE90 Drum thermistor abnormality: The output value of the
drum thermistor-K is out of a specified range.
P. 8-167
CF10 Finisher related
service call
Communication module SRAM reading failure. [MJ-1101/
1107]
P. 8-217
F070 Communication
related service call
Communication error between System-CPU and Engine-
CPU
P. 8-217
F090 Circuit related
service call
SRAM abnormality on the SYS board P. 8-179
F100_0 Other service call HDD format error: Operation of HDD key data fails. P. 8-219
F100_1
HDD format error: Encryption key data of either the SYS
board or the SRAM board for the SYS board are damaged
.
P. 8-219
F100_2 HDD format error: Encryption key data of both the SYS
board and the SRAM board for the SYS board are
damaged.
P. 8-220
F101_0 HDD connection error (HDD connection cannot be
detected.)
P. 8-221
F101_1 Root partition mount error (HDD formatting fails.): The
HDD cannot be connected (mounted) caused by damage
to the areas in which the program is mainly stored.
P. 8-221
F101_2 Partition mount error: The HDD cannot be connected
(mounted) caused by damage to areas other than those
described in the F101_1 and F101_4 to F101_9 errors.
P. 8-221
F101_3 Partition mount error: The HDD cannot be connected
(mounted) caused by damage to areas other than those
described in the F101_1 and F101_4 to F101_9 errors.
P. 8-221
F101_4 Partition mount error: The HDD cannot be connected
(mounted) caused by damage to the “/work” partition.
P. 8-222
F101_5 Partition mount error: The HDD cannot be connected
(mounted) caused by damage to the “/registration”
partition.
P. 8-223
F101_6 Partition mount error: The HDD cannot be connected
(mounted) caused by damage to the “/backup” partition.
P. 8-224
F101_7 Partition mount error: The HDD cannot be connected
(mounted) caused by damage to the “/imagedata”
partition.
P. 8-225
F101_8 Partition mount error: The HDD cannot be connected
(mounted) caused by damage to the “/storage” partition.
P. 8-226
F101_9 Partition mount error: The HDD cannot be connected
(mounted) caused by damage to the “/encryption”
partition.
P. 8-227
F102 HDD start error: HDD cannot become ‘Ready’ state. P. 8-228
Error code Classification Contents Troubleshooting
To Next Page
Loading...
