Home
VAT
Control Unit
615 Series
VAT 615 Series User Manual
4
of 1
of 1 rating
102 pages
Give review
Manual
Specs
To Next Page
To Next Page
To Previous Page
To Previous Page
Loading...
Installation, Operating & Maintenance Instructions
Series 615 DN 40 (I.D. 1
½
”), DeviceNet
VAT Vakuumventile AG, CH-9469 Haag, Sw
itzerland
Tel +41 81 771 61 61 Fax +41 81 771 48 30 CH@vatvalve.com www.vatvalve.com
603476
EA
2013
-
07
-
25
10
/
102
2.4
Admissible forces
Forces from the wei
ght of other components can lead to deformation o
f the valve body and to malfunction
of the valve. The
stress has to be relieved by
suitable means. The follow
ing forces are admissible:
Valve size
A
xial tensile or
compressiv
e force «F
A
»
Bending moment «M»
M
F
A
mm
inch
N
lb.
Nm
lbf.
50
2
150
34
11
8
9
11
Table of Contents
Default Chapter
3
Table of Contents
3
1 Use of Product
5
Technical Data
6
2 Installation
7
Unpacking
8
Installation into the System
8
Tightening Torque
9
Mounting of ISO-KF Flanges
9
Admissible Forces
10
Admissible Forces at Controller
11
Requirements to Sensor Connection
12
Electrical Connection
13
Ground Connection
13
Sensor Supply Concepts
14
Power and Sensor Connection ( 15 VDC Sensors) with Optional SPS Module
15
Devicenet Connection
16
Logic I/O
17
Digital Input
18
Digital Output
18
Service Port Connection
18
3 Operation
19
Introduction
19
Local Operation
20
Remote Operation
20
Safety Mode
21
Service Indication
21
Operation under Increased Temperature
21
Behavior During Power up
21
Behavior in Case of Power Failure
22
Display Information
23
Display Controller
23
Setup Procedure
24
Devicenet Configuration
25
Devicenet® Leds
27
LOGIC I/O Configuration
29
Valve Configuration
30
Sensor Configuration
30
Zero
31
Pressure Control Configuration
32
Close Valve
38
Open Valve
38
Position Control
39
Pressure Control
39
Pressure Control Operation with 2 Sensors
40
Tuning of Pressure Control Performance
40
Tuning of Pressure Control with Adaptive Algorithm
41
Tuning of Pressure Control Performance with Fixed Algorithm
46
Tuning of Control Performance with Soft Pump Algorithm
50
4 Devicenet Interface
53
Introduction
53
Factory Default Assemblies
54
Messaging Format
54
Explicit Messaging Connections
54
I/O Poll Messaging Connections
55
Object
56
Object Model for the Process Control Valve Device
56
Object Definition
57
Identity Object (Class ID 1)
58
Assembly Objects (Class ID 4)
58
Assembly Describtion
59
Connection Object (Class ID 5)
62
Discrete Input Object (Class ID 8)
63
Selection Object (Class ID 46)
63
S-Device Supervisor Object (Class ID 48)
64
S-Analog Sensor Object (Class ID 49)
67
S-Singel Stage Controller Object (Class ID 51)
70
Pressure Controller Object (Class ID 100)
73
Definition of Terms
74
5 Trouble Shooting
75
6 Maintenance & Repairs
78
Maintenance Procedures
79
Replacement of Plate O-Ring
80
Replacement of Shaft Feedtrough Seals and Plate O-Ring
83
Option Board
92
Durability of Power Fail Battery
92
Retrofit / Replacement Procedure
93
7 Drawing
97
8 Spare Parts
98
Valve Unit
98
Seal Kit
98
Control and Actuating Unit
99
Accessories
100
Centering Ring with Viton O-Ring
100
9 Warranty
101
4
Based on 1 rating
Ask a question
Give review
Questions and Answers:
Need help?
Do you have a question about the VAT 615 Series and is the answer not in the manual?
Ask a question
VAT 615 Series Specifications
General
Brand
VAT
Model
615 Series
Category
Control Unit
Language
English
Related product manuals
VAT 613 Series
149 pages
VAT 612 Series
116 pages
VAT 61532-KEAQ-0001
102 pages
VAT 650 Series
94 pages
VAT 653 Series
129 pages
VAT 651 Series
99 pages
VAT 642 Series
119 pages
VAT 65040 Series
51 pages
VAT 65048 Series
51 pages
VAT 29 Series
13 pages
VAT 021 Series
12 pages
VAT 02110-BA24-0001
12 pages
To Next PageTo Next PageTo Previous PageTo Previous Page
Loading...
Need help?
General
