Wirepath WPS-300-DVR - Page 107

107
WPS-300-DVR-9CH & 16CH Installation and Users Manual
•DEVICETYPE
Press the +/- buttons on the front panel of the DVR or on the remote control to change the device type
Alternatively use the mouse to select the appropriate setting. OPTIONS: PTZ, keyboard, (Recommended)
PTZ+keyboard or (Not Available).
NOTE: RS-232 device must be set to Keyboard.
•MODEL
Press +/- buttons to change the supported model (or protocol). Alternatively use the remote control to
change this setting. RS-232 model must be set to Terminal.
 •BAUDRATE
Press +/- buttons on the front panel of the DVR or on the remote control to change the Baud Rate
Alternatively use the remote control to change this setting. OPTIONS: 1200, 1800, 2400, 4800, 9600, 19200,
38400.
 •DATABIT
Press +/- buttons on the front panel of the DVR or on the remote control to change the Date Bit Alternatively
use the remote control to change this setting. OPTIONS: 5, 6, 7, 8, (Recommended).
 •STOPBIT
Press +/- buttons on the front panel of the DVR or on the remote control to change the Stop Bit Alternatively
use the remote control to change this setting. OPTIONS: 1, (Recommended) 2.
 •PARITY
Press +/- buttons on the front panel of the DVR or on the remote control to change the Parity. Alternatively
use the remote control to change this setting. OPTIONS: None, (Recommended) Odd, Even.
 •DVR/CAMERAID
Not congurable.
RS-485
ThefollowingisabriefdescriptionforeachitemintheRS-422/485MENUanditsspecicoperations:
NOTE: For RS-422/485, only the Model, Baud Rate and DVR/Camera ID settings should be congured for RS-485.
 •DEVICETYPE
Press the +/- buttons on the front panel of the DVR or on the remote control to change the device type.
Alternatively use the mouse to select the appropriate setting. OPTIONS: RS-485 device must be set to PTZ.
•MODEL
Press +/- buttons to change the supported model (or protocol). Alternatively use the remote control to
change this setting. OPTIONS: Pelco D Protocol Dome, Samsung SCC-641P, Kalatel Cyber Dome, PIH-Series,
Dynacolor, Bosch AutoDome, Video Trek, PTC-400C, VC-C4, Panasonic, Pelco(D-Others), SCC-641P, etc.
The
 NOTE:WirepathCamerasaredefaultedtoPelco(D-Type),Baudrateof4800.
 •BAUDRATE
Press +/- buttons on the front panel of the DVR or on the remote control to change the Baud Rate.
Alternatively use the remote control to change this setting. OPTIONS: 1200, 1800, 2400, 4800, 9600, 19200,
38400.
 •DATABIT
Press +/- buttons on the front panel of the DVR or on the remote control to change the Date Bit.
Alternatively use the remote control to change this setting. OPTIONS: 5, 6, 7, 8, (Recommended).
 •STOPBIT
Press +/- buttons on the front panel of the DVR or on the remote control to change the Stop Bit.
Alternatively use the remote control to change this setting. OPTIONS: 1, (Recommended) 2.
 •PARITY
Press +/- buttons on the front panel of the DVR or on the remote control to change the Parity. Alternatively
use the remote control to change this setting. OPTIONS: Odd, Even, None, (Recommended).
 •DVR/CAMERAID
Press +/- buttons to change the Camera ID. Alternatively use the remote control to change this setting.
OPTIONS: 0-255.
NOTE:TheCameraIDmustnotconictwithotherdevicesconnectedtotheRS-485network.