Xerox WorkCentre 4150

January 2016
2-31
WorkCentre 4150/4250/4260WorkCentre WorkCentre 4150/4250/42604150/
05-300
Status Indicator RAPs
05-300 DADF Jam 3 RAP
05-300 The lead edge of the document failed to actuate the duplex sensor within the correct
time in reverse mode.
Procedure
WARNING
Switch off the electricity to the machine. Disconnect the power cord from the customer
supply while performing tasks that do not need electricity. Electricity can cause death or
injury. Moving parts can cause injury.
Go to the relevant procedure:
• 4150 Checkout
• 4250/4260 Checkout
4150 Checkout
Refer to Wiring Diagram 11. Perform the following:
1. Raise the DADF input tray, PL 5.10 Item 5. Remove all jammed paper.
2. Check the document path for damage or obstructions.
3. Check the duplex gate, PL 5.25 Item 25 for damage. If necessary, install a new duplex
gate.
4. Check that the following components are clean and rotate freely.
• Exit roll, PL 5.20 Item 2.
• Exit roll idlers, PL 5.20 Item 20.
5. Check that the duplex sensor actuator, PL 5.25 Item 27 moves freely and is not damaged.
6. Enter dC330 code 05-170. Check the duplex sensor (Q05-170).
NOTE: The duplex sensor is mounted on the DADF PWB, PL 5.20 Item 6.
7. Enter code 05-220. Check that the DADF duplex motor, PL 5.25 Item 5 runs in the
reverse direction and drives the exit roll, PL 5.20 Item 2.
8. Check the wiring between the DADF duplex motor and CN5 on the DADF PWB.
9. Check the exit roll gear, PL 5.20 Item 5 for damage. If necessary, install a new exit roll
gear.
10. If necessary, install new components:
• DADF PWB, PL 5.20 Item 6.
• Duplex motor assembly, PL 5.25 Item 4.
• Document transport assembly, PL 5.10 Item 2.
4250/4260 Checkout
Refer to Wiring Diagram 29. Perform the following:
1. Raise the DADF input tray, PL 5.30 Item 11. Remove all jammed paper.
2. Open the DADF top cover assembly, PL 5.30 Item 2. Raise the pickup guide assembly,
PL 5.45 Item 1. Check the document path for damage or obstructions. If necessary, install
a new document transport assembly, PL 5.30 Item 26.
3. Check that the following components are clean and rotate freely.
•Duplex roll, PL 5.45 Item 8.
• Duplex roll idlers, PL 5.45 Item 20.
4. Remove the lower guide assembly, PL 5.50 Item 1. Check that the duplex sensor actua-
tor, PL 5.55 Item 5 moves freely and is not damaged.
5. Enter dC330 code 05-170. Check the duplex sensor (Q05-170), PL 5.55 Item 1. If neces-
sary, install a new duplex sensor, PL 5.55 Item 1.
6. Check the wiring between the duplex sensor and CN10 on the DADF PWB. If necessary,
install a new duplex sensor, PL 5.55 Item 1.
7. Enter code 05-220. Check that the DADF duplex motor, PL 5.30 Item 7 runs in the
reverse direction and drives the duplex roll, PL 5.45 Item 8.
8. Check the wiring between the DADF duplex motor and CN11 on the DADF PWB.
9. If necessary, install new components:
• Duplex motor assembly, PL 5.30 Item 7.
• DADF PWB, PL 5.30 Item 24.
• Document transport assembly, PL 5.30 Item 26.