Xerox WorkCentre 4150 Service Manual

January 2016
2-99
WorkCentre 4150/4250/4260WorkCentre WorkCentre 4150/4250/42604150/
OF1
Status Indicator RAPs
OF1 Unusual Noise RAP
Use this RAP to isolate and identify the source of unusual noises.
Procedure
WARNING
Switch off the electricity to the machine. Disconnect the power cord from the customer
supply while performing tasks that do not need electricity. Electricity can cause death or
injury. Moving parts can cause injury.
Perform the following:
1. Ask the customer if there are any specific machine functions that are noisy.
2. Identify the source of the noise by exercising the machine in all modes.
3. Use diagnostics to run individual components.
4. Go to the relevant subsection:
• Main Drives and Paper Transport
• LSU
• (4150) DADF
• (4250/4260) DADF
• Trays 2, 3, 4 and HCF
• Finisher
5. Refer to Possible Causes and Potential Solutions.
Main Drives and Paper Transport
• (4150) Enter dC330 code 04-100 to run the main BLDC motor.
The following components will be run:
– Xerographic module, PL 9.10 Item 1.
– Toner cartridge, PL 9.10 Item 2.
• (4250/4260) Enter dC330 code 04-100 to run the main BLDC motor. The xerographic
module, PL 9.10 Item 1 will be run.
• While the main BLDC motor runs, stack the code 08-810 to energize the tray 1 pickup
clutch and run the tray 1 feed rolls, PL 7.15 Item 20 and PL 8.10 Item 12.
• While the main BLDC motor runs, stack the code 08-850 to energize the registration
clutch and run the registration roll, PL 4.15 Item 1.
• While the main BLDC motor runs, stack the code 08-800 to energize the bypass feed
clutch and run the bypass tray feed rolls, PL 8.20 Item 17 and PL 8.20 Item 23.
• While the main BLDC motor runs, stack the code 08-860 to energize the duplex feed
clutch and run the duplex feed rolls, PL 7.30 Item 10 and PL 7.30 Item 12.
• (4150) Enter dC330 code 09-600 to run the toner dispense motor, PL 4.20 Item 3.
• (4250/4260) Enter dC330 code 09-600 to run the toner dispense motor, PL 4.25 Item 3.
•Enter dC330 code 04-300 or 04-310 to run the duplex motor in forward or reverse. The
duplex roll, PL 10.15 Item 9 will rotate.
•Enter dC330 code 10-400 to run the fuser motor. The fuser rolls will rotate.
•Enter dC330 code 04-200 to run the exit motor. The upper exit roll, PL 10.15 Item 23 will
rotate.
•Enter dC330 code 04-400 to run the duplex fans, PL 7.35 Item 16 and PL 7.35 Item 17.
•Enter dC330 code 10-500 to run the fuser fan, PL 4.15 Item 18.
• Enter dC330 code 09-500 to run the SMPS fan, PL 4.15 Item 18.
• Enter dC330 code 06-300 to run the LSU fan, PL 6.10 Item 3.
LSU
• Enter dC330 code 06-100 to run the LSU motor.
(4150) DADF
• Enter dC330 code 05-200 to run the DADF scan motor, PL 5.25 Item 12.
The following components will be run:
– Scan roll, PL 5.25 Item 23.
–Gate roll, PL 5.25 Item 15.
– Duplex roll, PL 5.25 Item 22.
• While the DADF scan motor runs, stack the code 05-300 to energize the pickup clutch
and run the DADF feed rolls, PL 5.15 Item 5.
• While the DADF scan motor runs, stack the code 05-310 to energize the registration
clutch and run the registration roll, PL 5.15 Item 21.
• Enter dC330 code 05-210 to run the DADF duplex motor, PL 5.25 Item 5. The exit roll, PL
5.20 Item 2 will rotate.
(4250/4260) DADF
• Enter dC330 code 05-200 to run the DADF scan motor, PL 5.30 Item 6.
The following components will be run:
–Gate roll, PL 5.50 Item 18.
– Duplex roll, PL 5.45 Item 8.
• While the DADF scan motor runs, stack the code 05-300 to energize the pickup clutch
and run the DADF feed rolls, PL 5.40 Item 7.
• While the DADF scan motor runs, stack the code 05-310 to energize the registration
clutch and run the CVT roll, PL 5.50 Item 19.
• Enter dC330 code 05-210 to run the DADF exit motor, PL 5.30 Item 7. The upper exit roll,
PL 5.45 Item 20 and lower exit roll PL 5.55 Item 10 will rotate.
(4265) DADF
TBD - Will be completed when DC330 codes are finalized.
Trays 2, 3, 4 and HCF
• Enter dC330 code 08-920 to run the tray 2 feed motor, PL 7.20 Item 9. The tray 2 feed
rolls, PL 7.25 Item 11 and PL 8.10 Item 12 will rotate.
• Enter dC330 code 08-930 to run the tray 3 feed motor, PL 7.20 Item 9. The tray 3 feed
rolls, PL 7.25 Item 11 and PL 8.10 Item 12 will rotate.
• Enter dC330 code 08-940 to run the tray 4 feed motor, PL 7.20 Item 9. The tray 4 feed
rolls, PL 7.25 Item 11 and
PL 8.10 Item 12 will rotate.
• Enter dC330 code 08-930 to run the HCF feed motor, PL 7.50 Item 19. The HCF feed
rolls, PL 7.50 Item 10 and PL 8.10 Item 12 will rotate.
Finisher
• Enter dC330 code 12-100 to run the entrance motor, PL 12.15 Item 5.
The following components will be run:
– Entry roll, PL 12.15 Item 2.
– Transport roll, PL 12.15 Item 2.
• Enter dC330 code 12-110 to run the exit motor, PL 12.20 Item 10.

Xerox WorkCentre 4150 Specifications

General

Brand	Xerox
Model	WorkCentre 4150
Category	All in One Printer
Language	English