YASKAWA E-7 Series User Manual

3.2 Operating Procedures for Utility Functions
3.2.34 Program Table Edit/Save (FnB03)
3-112
 DEC: Deceleration
 POUT: Programmable Output Signals
 EVENT: Pass Condition
 LOOP: Number of Executions
 NEXT: PGMSTEP to be Executed Next
㹂㹃㹁㸮㸮㸮㸻㸯㸰㸱㸲㸳㸴㸵㸶
㹂㹃㹁㸮㸮㸮㸻㸯㸰 㸱㸲㸳㸴㸵㸶
Move cursor Change deceleration
㹂㹃㹁㸮㸮㸮㸻㸯㸱 㸱㸲㸳㸴㸵㸶
If the value becomes less than 1,
“:” is displayed.
㹎㹍㹓㹒㸮㸮㸮㸻㹌㸿㹘㸸㹌㸿㹘㸸
㹎㹍㹓㹒㸮㸮㸮㸻㹌㸿㹘㸸㹌㸿㹘㸸
Move cursor Change programmable output signal
Pressing the key changes the display
in the following order.
N → A → Z → :
㹎㹍㹓㹒㸮㸮㸮㸻㹌㹌㹘㸸㹌㸿㹘㸸
Pressing the key changes the display
in the reverse order.
㹃㹔㹒㸮㸮㸮㸻㹒㸯㸰㸱㸲㸳  㹃㹔㹒㸮㸮㸮㸻㹒㸯㸰㸱㸲㸳 
Move cursor
Move cursor

Move cursor
㹃㹔㹒㸮㸮㸮㸻㹇㹒㸯㸰㸱㸲㸳

㹃㹔㹒㸮㸮㸮㸻㹌㹒㸯㸰㸱㸲㸳

㹃㹔㹒㸮㸮㸮㸻㹂㹒㸯㸰㸱㸲㸳

㹃㹔㹒㸮㸮㸮㸻㹑㹃㹊㸮㹒㸯㸰㸱㸲㸳
㹃㹔㹒㸮㸮㸮㸻㹑㹃㹊㸯㹒㸯㸰㸱㸲㸳

㹃㹔㹒㸮㸮㸮㸻㹑㹃㹊㸵㹒㸯㸰㸱㸲㸳
㹃㹔㹒㸮㸮㸮㸻㸸
Change elapsed time
㹃㹔㹒㸮㸮㸮㸻㹒㸰㸰㸱㸲㸳

㹃㹔㹒㸮㸮㸮㸻㹇㹒㸯㸰㸱㸲㸳

㹃㹔㹒㸮㸮㸮㸻㹇㹒㸰㸰㸱㸲㸳

㹃㹔㹒㸮㸮㸮㸻㹌㹒㸯㸰㸱㸲㸳

㹃㹔㹒㸮㸮㸮㸻㹌㹒㸰㸰㸱㸲㸳

㹃㹔㹒㸮㸮㸮㸻㹂㹒㸯㸰㸱㸲㸳

㹃㹔㹒㸮㸮㸮㸻㹂㹒㸰㸰㸱㸲㸳

㹃㹔㹒㸮㸮㸮㸻㹑㹃㹊㸮㹒㸯㸰㸱㸲㸳
㹃㹔㹒㸮㸮㸮㸻㹑㹃㹊㸯㹒㸯㸰㸱㸲㸳

㹃㹔㹒㸮㸮㸮㸻㹑㹃㹊㸮㹒㸰㸰㸱㸲㸳
㹃㹔㹒㸮㸮㸮㸻㹑㹃㹊㸯㹒㸰㸰㸱㸲㸳



㹃㹔㹒㸮㸮㸮㸻㹑㹃㹊㸵㹒㸯㸰㸱㸲㸳

㹃㹔㹒㸮㸮㸮㸻㹑㹃㹊㸵㹒㸰㸰㸱㸲㸳

Change elapsed time
Change elapsed time
Change elapsed time
Change elapsed time
Change elapsed time
Change elapsed time
Change pass
condition

Move cursor
Change pass
condition
Move cursor
Change pass
condition
Move cursor
Change pass
condition
Move cursor
Change pass
condition
Change pass
condition
Change pass condition
㹊㹍㹍㹎㸮㸮㸮㸻㸮㸮㸮㸮㸯
㹊㹍㹍㹎㸮㸮㸮㸻㸮㸮㸮㸮㸯
Move cursor Change number of executions
㹊㹍㹍㹎㸮㸮㸮㸻㸮㸯㸮㸮㸯
㹌㹃㹖㹒㸮㸮㸮㸻㸮㸮㸮㸮㸮
㹌㹃㹖㹒㸮㸮㸮㸻㸮㸮㸮㸮㸮
Move cursor Change next PGMSTEP to be executed
㹌㹃㹖㹒㸮㸮㸮㸻㸮㸮㸰㸳㸳
If the value becomes less than 0,
“END” is displayed.

YASKAWA E-7 Series Specifications

General

Brand	YASKAWA
Model	E-7 Series
Category	Servo Drives
Language	English