YASKAWA E-7 Series User Manual

3.2 Operating Procedures for Utility Functions
3.2.34 Program Table Edit/Save (FnB03)
3-111
3
Utility Functions
Details on How to Set Table Settings
Details on the setting method for step 5 in Editing Program Table on
page 3-108 are shown below.
If the number of display digits is exceeded when Expansion Mode is
enabled (PnB54 = 1), the table name will be abbreviated. Refer to the
following manual for details.
Σ-7-Series Σ-7S SERVOPACK Command Option Attachable Type with
INDEXER Module Product Manual (Manual No.: SIEP S800001 64)
 POS: Target Position
 SPD: Positioning Speed
 RDST: Registration Distance
 RSPD: Registration Speed
 ACC: Acceleration
㹎㹍㹑㸮㸮㸮㸻㹑㸩㸯㸰㸱㸲㸳㸴㸵㸶
㹎㹍㹑㸮㸮㸮㸻㸩㹇㹌㹄㹇㹌㹇㹒㹃
㹎㹍㹑㸮㸮㸮㸻㸫㹇㹌㹄㹇㹌㹇㹒㹃
㹎㹍㹑㸮㸮㸮㸻㸫㸫㸫
㹎㹍㹑㸮㸮㸮㸻㹑㸩㸯㸰㸱㸲㸳㸴㸵㸶
Move cursor
Change target position
㹎㹍㹑㸮㸮㸮㸻㹑㸩㸰㸰㸱㸲㸳㸴㸵㸶
㹎㹍㹑㸮㸮㸮㸻㸿㸩㸯㸰㸱㸲㸳㸴㸵㸶
Move cursor
㹎㹍㹑㸮㸮㸮㸻㸿㸩㸰㸰㸱㸲㸳㸴㸵㸶
Change target position
㹎㹍㹑㸮㸮㸮㸻㹇㸩㸯㸰㸱㸲㸳㸴㸵㸶
㹎㹍㹑㸮㸮㸮㸻㹇㸩㸯㸰㸱㸲㸳㸴㸵㸶
Move cursor
㹎㹍㹑㸮㸮㸮㸻㹇㸩㸰㸰㸱㸲㸳㸴㸵㸶
Change target position
㹎㹍㹑㸮㸮㸮㸻㹑㹒㹍㹎
㹎㹍㹑㸮㸮㸮㸻㸿㸩㸯㸰㸱㸲㸳㸴㸵㸶
Change positioning
type
Change positioning
type
Change positioning
type
Change positioning
type
Change positioning
type
Change positioning
type
㹑㹎㹂㸮㸮㸮㸻㸯㸰㸱㸲㸳㸴㸵㸶
㹑㹎㹂㸮㸮㸮㸻㸯㸰 㸱㸲㸳㸴㸵㸶
Move cursor Change positioning speed
㹑㹎㹂㸮㸮㸮㸻㸯㸱 㸱㸲㸳㸴㸵㸶
㹐㹂㹑㹒㸮㸮㸮㸻㸯㸰㸱㸲㸳㸴㸵㸶
㹐㹂㹑㹒㸮㸮㸮㸻㸯㸰 㸱㸲㸳㸴㸵㸶
Move cursor Change registration distance
If the value becomes less than 0,
“−” is displayed.
㹐㹂㹑㹒㸮㸮㸮㸻㸯㸱㸱㸲㸳㸴㸵㸶
㹐㹑㹎㹂㸮㸮㸮㸻㸯㸰㸱㸲㸳㸴㸵㸶
㹐㹑㹎㹂㸮㸮㸮㸻㸯㸰㸱㸲㸳㸴㸵㸶
Move cursor Change registration speed
㹐㹑㹎㹂㸮㸮㸮㸻㸯㸱㸱㸲㸳㸴㸵㸶
㸿㹁㹁㸮㸮㸮㸻㸯㸰㸱㸲㸳㸴㸵㸶
㸿㹁㹁㸮㸮㸮㸻㸯㸰 㸱㸲㸳㸴㸵㸶
Move cursor Change acceleration
If the value becomes less than 1,
“:” is displayed.
㸿㹁㹁㸮㸮㸮㸻㸯㸱 㸱㸲㸳㸴㸵㸶

YASKAWA E-7 Series Specifications

General

Brand	YASKAWA
Model	E-7 Series
Category	Servo Drives
Language	English