1.3 Parameter Table
36 YASKAWA ELECTRIC TOEP C710687 03B FSDrive-MV1000 Parameter Guide
d1-11
(28CH)
Frequency
Reference 11
Sets the frequency reference for the drive. Setting units are determined by
parameter o1-03.
Default: 0.00 Hz
Min: 0.00 Hz
Max: 120.00 Hz
<20>
140
d1-12
(28DH)
Frequency
Reference 12
Sets the frequency reference for the drive. Setting units are determined by
parameter o1-03.
Default: 0.00 Hz
Min: 0.00 Hz
Max: 120.00 Hz
<20>
140
d1-13
(28EH)
Frequency
Reference 13
Sets the frequency reference for the drive. Setting units are determined by
parameter o1-03.
Default: 0.00 Hz
Min: 0.00 Hz
Max: 120.00 Hz
<20>
140
d1-14
(28FH)
Frequency
Reference 14
Sets the frequency reference for the drive. Setting units are determined by
parameter o1-03.
Default: 0.00 Hz
Min: 0.00 Hz
Max: 120.00 Hz
<20>
140
d1-15
(290H)
Frequency
Reference 15
Sets the frequency reference for the drive. Setting units are determined by
parameter o1-03.
Default: 0.00 Hz
Min: 0.00 Hz
Max: 120.00 Hz
<20>
140
d1-16
(291H)
Frequency
Reference 16
Sets the frequency reference for the drive. Setting units are determined
according to the frequency reference selection/display unit setting (o1-03).
Default: 0.00 Hz
Min: 0.00 Hz
Max: 120.00 Hz
<20>
140
d1-17
(292H)
Jog Frequency
Reference
Sets the Jog frequency reference. Setting units are determined by parameter
o1-03.
Default: 6.00 Hz
Min: 0.00 Hz
Max: 120.00 Hz
<20>
140
d2: Frequency Upper/Lower Limits
d2-01
(289H)
Frequency
Reference Upper
Limit
Sets the frequency reference upper limit as a percentage of the maximum
output frequency.
Default: 100.0%
Min: 0.0%
Max: 110.0%
142
d2-02
(28AH)
Frequency
Reference Lower
Limit
Sets the frequency reference lower limit as a percentage of the maximum
output frequency.
Default: 0.0%
Min: 0.0%
Max: 110.0%
142
d2-03
(293H)
Master Speed
Reference Lower
Limit
Sets the lower limit for frequency references from analog inputs as a
percentage of the maximum output frequency.
Default: 0.0%
Min: 0.0
Max: 110.0%
142
d3: Jump Frequency
d3-01
(294H)
Jump Frequency 1
Eliminates problems with resonant vibration of the motor/machine by
avoiding continuous operation in predefined frequency ranges. The drive
accelerates and decelerates the motor through the prohibited frequency
ranges.
Setting 0.0 disables this function.
Parameters must be set so that d3-01 ≥ d3-02 ≥ d3-03.
Default: 0.0 Hz
Min: 0.0 Hz
Max: 120.0 Hz
<20>
143
d3-02
(295H)
Jump Frequency 2 143
d3-03
(296H)
Jump Frequency 3 143
d3-04
(297H)
Jump Frequency
Width
Sets the dead-band width around each selected prohibited frequency
reference point.
Default: 1.0 Hz
Min: 0.0 Hz
Max: 20.0 Hz
143
d4: Frequency Reference Hold and Up/Down 2 Function
d4-01
(298H)
Frequency
Reference Hold
Function Selection
0: Disabled. Drive starts from zero when the power is switched on.
1: Enabled. At power up, the drive starts the motor at the Hold frequency
that was saved.
Default: 0
Min: 0
Max: 1
144
d4-03
(2AAH)
Frequency
Reference Bias Step
(Up/Down 2)
Sets the bias added to the frequency reference when the Up 2 and Down 2
contact inputs are enabled (H1- = 75, 76).
Default: 0.00 Hz
Min: 0.00 Hz
Max: 99.99 Hz
146
No.
(Addr.)
Name Description Setting Page
MV1000ParameterGuide_E_conditional.book 36 ページ ２０１３年１０月１１日 金曜日 午後８時１８分
To Next Page
Loading...
