1.3 Parameter Table
32 YASKAWA ELECTRIC TOEP C710687 03B FSDrive-MV1000 Parameter Guide
u C: Tuning
C parameters adjust the acceleration and deceleration times, S-curve characteristics, slip compensation, and torque
compensation.
No.
(Addr.)
Name Description Setting Page
C1: Acceleration and Deceleration Times
C1-01
(200H)
Acceleration Time 1
Sets the time to accelerate from 0 to maximum frequency.
Default: 60.0 s
Min: 0.0 s
Max: 6000.0 s
<12>
128
C1-02
(201H)
Deceleration Time 1
Sets the time to decelerate from maximum frequency to 0.
Default: 120.0 s
Min: 0.0 s
Max: 6000.0 s <12>
128
C1-03
(202H)
Acceleration Time 2
Sets the time to accelerate from 0 to maximum frequency.
Default: 60.0 s
Min: 0.0 s
Max: 6000.0 s
<12>
128
C1-04
(203H)
Deceleration Time 2
Sets the time to decelerate from maximum frequency to 0.
Default: 120.0 s
Min: 0.0 s
Max: 6000.0 s <12>
128
C1-05
(204H)
Acceleration Time 3
(Motor 2 Accel
Time 1)
Sets the time to accelerate from 0 to maximum frequency.
Default: 60.0 s
Min: 0.0 s
Max: 6000.0 s <12>
128
C1-06
(205H)
Deceleration Time 3
(Motor 2 Decel
Time 1)
Sets the time to decelerate from maximum frequency to 0.
Default: 120.0 s
Min: 0.0 s
Max: 6000.0 s <12>
128
C1-07
(206H)
Acceleration Time 4
(Motor 2 Accel
Time 2)
Sets the time to accelerate from 0 to maximum frequency.
Default: 60.0 s
Min: 0.0 s
Max: 6000.0 s <12>
128
C1-08
(207H)
Deceleration Time 4
(Motor 2 Decel
Time 2)
Sets the time to decelerate from maximum frequency to 0.
Default: 120.0 s
Min: 0.0 s
Max: 6000.0 s <12>
128
C1-09
(208H)
Fast Stop Time
Sets the time for the Fast Stop function.
Default: 120.0 s
Min: 0.0 s
Max: 6000.0 s
<12>
130
C1-10
(209H)
Accel/Decel Time
Setting Units
0: 0.01 s (0.00 to 600.00 s)
1: 0.1 s (0.0 to 6000.0 s)
Default: 1
Min: 0
Max: 1
130
C1-11
(20AH)
Accel/Decel Time
Switching
Frequency
Sets the frequency to switch between accel/decel time settings.
Default:
<10>
Min: 0.0 Hz
Max: 120.0 Hz
129
C2: S-curve Characteristic
C2-01
(20BH)
S-Curve
Characteristic at
Accel Start
The S-curve can be controlled at the four points shown below.
Default:
<10>
Min: 0.00 s
Max: 10.00 s
130
C2-02
(20CH)
S-Curve
Characteristic at
Accel End
Default: 0.20 s
Min: 0.00 s
Max: 10.00 s
130
C2-03
(20DH)
S-Curve
Characteristic at
Decel Start
Default: 0.20 s
Min: 0.00 s
Max: 10.00 s
130
C2-04
(20EH)
S-Curve
Characteristic at
Decel End
Default: 0.00 s
Min: 0.00 s
Max: 10.00 s
130
C2-01 C2-04
C2-02 C2-03
ON
OFF
RUN
command
Time
Output
frequency
MV1000ParameterGuide_E_conditional.book 32 ページ ２０１３年１０月１１日 金曜日 午後８時１８分
To Next Page
Loading...
